- Project plans
- Project activities
- Legislation and standards
- Industry context
Last edited 23 Jan 2018
To help develop this article, click 'Edit this article' above.
Bridges are a common feature of the built environment and one of the key elements of civil engineering. The basic principles of bridge design are dependent on the load-bearing structure; whether flat, convex or concave. These are better known as beam, arch or suspension bridges:
Beam bridges are either simple beam or cantilever structures generally constructed from steel truss or pre-stressed concrete units. The simple beam bridge is horizontally self-supporting and transmits loads vertically through piers or abutments. The cantilever bridge transmits loads through piers central to the beam.
Arch bridges consist of a load-bearing arch in a state of compression, the strength and stability of which allows them to carry greater loads than beam bridges. The arch can support the horizontal deck of the bridge either from above or below.
Suspension bridges consist of towers secured by cables that suspend the central structural span or deck. The tower foundations may be constructed using caisson or cofferdam techniques, whilst the cable anchorages can be secured through anchorage tunnels to suitable ground on either end of the bridge.
From these three basic options, a very wide range of designs are possible. The choice of bridge design will be determined by the height, ground conditions and the clear span required.
Traditionally, steel construction has been most commonly used for very long spans, however, concrete arches are now also being used for big bridges. For large single-spans bridges, suspension bridges are the most common, with the high-tensile strength of the steel cables providing a design solution that is very economical compared to other support options.
Moveable bridges are moveable variations of the three basic forms, generally used in situations where greater headroom under the bridge is sometimes necessary, for example to allow the passage of a ship underneath. The most common types of moveable bridge are:
- Swing: The structure pivots on a central pier.
- Bascule or pivoted cantilever: 'Drawbridges' which use a counter-weight behind the pivot point to raise and lower the deck.
- Vertical lift: Simple beams or girders that are raised by cables from towers.
 Construction of bridges
There are a very wide range of construction methods available, however, bridge foundations constructed in water will usually involve the use of cofferdams or caissons. Foundations on land may be piled, often capped off to receive a pier foundation.
Piers will generally be constructed above the foundations, and then beams or girders lifted on to them by crane which can either be erected on falsework around the pier or from ground level. After the main girders have been placed, the bridge deck can be positioned or cast in situ.
- Steel trough filled with concrete.
- Steel beams encased with concrete.
- Reinforced concrete slab on steel beams.
- Steel deck on steel beams.
If the bridge is to span water, barges or pontoons may be used to float materials out to the lifting position. A temporary system of trestles may be used as a means of placing the beams or girders. For bridges spanning high drops, plate-girders or trussed-girders may be hauled across the opening using rollers. Alternatively, cantilever launching may be used, where the beam is launched from one bank, with sufficient ballast to counteract the overturning force, and hauled across the span using a winch.
- Supporting the arch using trestles until construction is complete. This is suitable for low arch bridges.
- Cantilevering the ribs out from the sides of the span. This is suitable for bridges over high drops which cannot be spanned with trestles.
Where the spans are very large, the arch may be cantilevered in sections using a creeping crane that is mounted on top of the arch. The crane lifts rib sections from barges or pontoons below. The bridge deck is then constructed from both ends, meeting in the middle.
For more information, see Arches.
The anchorage foundations are usually constructed deep into a hillside on both banks. The towers are typically constructed using steel or in situ concrete, built on large concrete bases. Cable housings generally take the form of massive concrete blocks either positioned in water at either bank or cast deep into the bank itself.
Multi-strands of high tensile wire are used to build up the suspension cables, which are then carried between anchorage points by means of a grooved wheel.
Bridge bearings provide a resting surface between supporting piers and the deck. They act to reduce the stresses that are involved by allowing controlled movement. They are usually made of metal or flexible materials such as rubber or plastic laminates.
Expansion joints can be formed to accommodate movement in the bridge deck. The most common types are:
 Interlocking comb joint
Buried joints with a strip of surfacing over the joint to accommodate movement. These are inexpensive and quick to install, although their life-span is variable.
 Elastomeric in metal runners (EMRs)
Joints formed with elastomeric material fixed in metal runners.
 Reinforced elastomeric joints (REJs)
Elastomer reinforced with metal plates on both sides of the joint.
 Bridge failures
Early suspension bridges were susceptible to vibration when an external periodic frequency matched the bridge's natural structural frequency. This could cause it to become structurally unstable and ultimately could cause catastrophic collapse.
Famously, this is why marching soldiers 'broke step' as they crossed certain bridges. Broughton Suspension Bridge collapsed in 1831, and more recently, Tacoma Narrows Bridge collapsed in 1940. Whilst modern suspension bridge design should eliminate such instability, in 2000, the Millennium Bridge in London began to vibrate when large crowds walked across it on its opening. It had to be closed for a year whilst dampeners were designed and installed.
In 2007, an eight-lane, steel-truss-arch bridge across the Mississippi River collapsed killing 13 people. Subsequently, a 2016 report by the American Road & Transportation Builders Association (ARBTA) suggested that almost 10% of America's bridges were in need of repair, that is, they achieved a score of four or less out of nine, when assessed by federal engineers.
 Related articles on Designing Buildings Wiki:
- 3D printed bridge.
- 7 Engineering Wonders of the World.
- Akashi Kaikyo Bridge.
- Assessing bridges.
- Barrel vault.
- Braced frame.
- Bridges of the world.
- Civil engineer.
- Dam construction.
- Garden bridge.
- Optimal arch bridge.
- Pile foundations.
- Prestressed concrete.
- State Route 520 Floating Bridge.
- Structural steelwork.
- Railway engineering.
- River engineering.
- Road construction.
- Road joints.
- Runway construction.
- The Iron Bridge
- The Millau Viaduct.
- Types of structural load.
 External references
- 'Introduction to Civil Engineering Construction' (3rd ed.), HOLMES, R., The College of Estate Management (1995)
Featured articles and news
Book review – a series of essays about architecture and urbanism in the British Empire.
The complex situation where events occur at the same time.
How can Latin America and the Caribbean unlock the digital potential of their new and existing built environment?
CIOB publish a new code of estimating practice.
These relate to a programme where each activity is allocated a price and interim payments made against completion.
Police testing finds that flat door could only withstand fire for half its designed time.
Have a look at these images from a new photography book of buildings being reclaimed by nature.
What does the phrase 'demised premises' mean? Find out here in our introductory article.
New good practice guidance looks at the best way to deliver multi-functional solar car parks.
Philip Hammond suggests the public finances have reached a turning point.
Support grows for the Construction (Retention Deposit Schemes) Bill.