Types of column
Contents |
[edit] Introduction
A column is a vertical structural member intended to transfer a compressive load. For example, a column might transfer loads from a ceiling, floor or roof slab or from a beam, to a floor or foundations.
Columns are typically constructed from materials such as stone, brick, block, concrete, timber, steel, and so on, which have good compressive strength.
[edit] Classical stone columns
In classical architecture, columns are often highly decorated, with standard designs including Ionic, Doric and Corinthian, and so on.
See Elements of classical columns for more information.
A colonnade is a row of columns spaced at regular intervals that can be used to support a horizontal entablature, an arcade or covered walkway, or as part of a porch or portico.
See: Colonnade for more information.
[edit] Steel columns
Steel columns have good compressive strength, but have a tendency to buckle or bend under extreme loading. This can be due to their:
The cross-sectional area and the section shape are incorporated into a geometric property of section, known as the radius of gyration. This refers to the distribution of an object's components around an axis. It can be calculated:
r = √I/A
Where, I = 2nd moment of area, A = cross-sectional area.
[edit] Slenderness ratio
The slenderness ratio is the effective length of a column in relation to the least radius of gyration of its cross-section. If this ratio is not sufficient then buckling can occur.
Column slenderness can be classified as:
- Long or slender: The length of the column is greater than the critical buckling length. Mechanical failure would typically occur due to buckling. The behaviour of long columns is dominated by the modulus of elasticity, which measures a column's resistance to being deformed elastically (i.e. non-permanently) when a force is applied.
- Short: The length of the column is less than the critical buckling length. Mechanical failure would typically occur due to shearing.
- Intermediate: In between the long and short columns, and its behaviour is dominated by the strength limit of the material.
Classification will depend on the column's geometry (i.e. its slenderness ratio) and its material properties (i.e. Young's modulus and yield strength).
[edit] Shape
Columns can be classified according to their cross sectional shape. Common column shapes include:
- Rectangular.
- Square.
- Circular.
- Hexagonal
- Octagonal.
In profile, they can be tapered, non-tapered, or 'barrel' shaped, their surface can be plain, fluted, twisted, panelled, and so on.
Columns may be of a simple uniform design, or they may consist of a central 'shaft' sitting on a column base, and topped by a 'capital'. See Elements of classical columns for more information.
[edit] Reinforced concrete columns
Reinforced concrete columns have an embedded steel mesh (known as rebar) to provide reinforcement.
The design of reinforcement can be either spiral or tied.
- Spiral columns are cylindrical with a continuous helical bar wrapped around the column. This spiral provides support in the transverse direction.
- Tied columns have closed lateral ties spaced approximately uniformly across the column. The spacing of the ties is limited in that they must be close enough to prevent failure between them, and far enough apart that they do not interfere with the setting of the concrete.
[edit] Other types of column
[edit] Stone column
Stone columns (or vibro stone columns) are formed by granular aggregate that is inserted into column shaped excavations and then compacted to improve the load bearing capacity of soil and fill material.
[edit] Pilotis
Pilotis are supports that lift a building above the ground or a body of water. In timber form, they were traditionally used in the vernacular architecture of Asia and Scandinavia, or wherever indigenous peoples lived at a water’s edge. They may also be used in hurricane or flood-prone areas, to raise the structure above storm surge levels.
The pioneer of modern pilotis was the architect Le Corbusier, who used them both functionally as ground-level supporting columns, and philosophically as a tool for freeing the rigidity of traditional plan layouts, enabling efficient, buildings as 'machines for living'.
See Pilotis for more information.
[edit] Piers
the term ‘pier’ can be used interchangeably for several different building elements. In general, it is an upright support for a structure or superstructure, but it can also refer to the sections of load-bearing structural walls between openings and different types of column.
See: Piers for more information.
[edit] Posts
The word 'post' is interchangeable with the word column, although is is typically used in relation to smaller structural members that may in some cases be independent, rather than part of a wider structure.
[edit] Knotted
A knotted column is a stone support that is carved in the shape of two or four columns joined by a knot. The knot in the columns is meant to represent various spiritual messages associated with humanity and its relationship to the Holy Trinity.
See: Knotted column for more information.
[edit] Colonnette
A slender supporting column often found at the corner of a shop lobby.
For more information see: Colonnette
[edit] Related articles on Designing Buildings
- Anta.
- Braced frame.
- Column formwork.
- Colonnette
- Concept structural design of buildings.
- Concrete-steel composite structures.
- Difference between pillars and columns.
- Elements of classical columns.
- Elements of structure in buildings.
- Fluting.
- Herm.
- Knotted column
- Piers.
- Pilotis.
- Portico.
- Post.
- Rebar.
- Reinforced concrete.
- Scagliola.
- Slenderness.
- Structural steelwork.
- Types of beam.
- Types of structure.
Featured articles and news
Heat pump announcements, what homeowners need to know
An 'ultimate guide to heat pumps' from a heating company.
Construction contract awards reach £7.1bn in February
Their highest level in seven months.
The journey to sustainability in heritage
Research is the key to better understanding.
Heritage approaches to adaptation, mitigation and loss.
Bridging the gap between policy, finance and installation.
Development on brownfield land
Definition, background, policy and the latest consultation.
With the Design Framework for Building Services.
Retrofit of Buildings, a CIOB Technical Publication
Pertinent technical issues, measures and the roles involved.
ECA joins HSE campaign to support mental health
Working Minds’ five simple steps based on risk assessment.
Mental health in the construction industry
Mental health issues in brief with related articles.
Transitional arrangements, Building Control and the BSR.
For pre-October buildings with substantial progress by April.
How to write an inspection and test plan
ITPs for quality control and assurance particular elements.
Why quality counts in domestic ventilation systems
From products, to systems to the installation.
Empowering the Future with CIOB Academy
Lifelong learning, upscaling, and reskilling for the built environment.
Winners of the 2024 ASBP Awards
Project, Product and Initiative according to the 6 pillars.
Comments