Approved Document C
The first set of national building standards was introduced in 1965. Now known as the building regulations, they set out:
- What qualifies as 'building work' and so fall under the control of the regulations.
- What types of buildings are exempt.
- The notification procedures that must be followed when starting, carrying out, and completing building work.
- Requirements for specific aspects of building design and construction.
The 'approved documents' provide guidance for how the building regulations can be satisfied in common building situations. There is no obligation to adopt the solutions presented in the approved documents, the building regulations can be satisfied in other ways.
Approved Document C: Site preparation and resistance to contaminants and moisture, was last published in 2013.
It covers the weather-tightness and water-tightness of buildings, subsoil drainage, site preparation, and measures to deal with contaminated land, radon, methane, and other site related hazardous and dangerous substances.
In terms of resistance to moisture, the regulations state that the building should be protected from harmful effects caused by:
- Ground moisture.
- Precipitation including wind-driven spray.
- Interstitial and surface condensation.
- Spillage of water from, or associated with, sanitary fittings or fixed appliances.
It defines a ‘contaminant’ as ‘any substance which is or may become harmful to persons or buildings, including substances which are corrosive, explosive, flammable, radioactive or toxic’; and lists examples of sites likely to contain contaminants, including:
- Animal and animal products processing works.
- Asbestos works.
- Ceramics and asphalt manufacturing works.
- Chemical works.
- Dockyards and dockland.
- Gas works.
- Landfill and other waste disposal sites.
- Oil storage and distribution sites.
- Power stations.
- Scrap yards.
- Sewage works.
- Texile and dye works.
The content of the Approved Document includes:
- Section 1: Clearance or treatment of unsuitable material – This includes guidance on various site investigation measures and types of unsuitable material.
- Section 2: Resistance to contaminants – This includes risk assessment and remedial guidance on solid and liquid contaminants, methane and other gases from the ground, and radon.
- Section 3: Subsoil drainage.
- Section 4: Floors – This includes guidance and technical solutions for ground supported floors, suspended timber ground floors, suspended concrete ground floors, floors exposed from below, and resistance to surface condensation and mould growth.
- Section 5: Walls – This includes guidance and technical solutions for internal and external walls (moisture from the ground), external walls (moisture from outside), solid external walls, cavity external walls, cavity insulation, framed external walls, cracking of external walls, impervious cladding systems, joints between doors and windows, door thresholds, and resistance of external walls to damage from interstitial condensation, surface condensation and mould growth.
- Section 6: Roofs – This includes guidance and technical solutions for roof resistance to damage from moisture from outside, interstitial condensation, surface condensation and mould growth.
[edit] Related articles on Designing Buildings
- Approved documents.
- Approved Document D.
- Approved Document F.
- Approved Document H.
- Brownfield land.
- Building Regulations.
- Condensation.
- Contaminated land.
- Cover systems for land regeneration - thickness of cover systems for contaminated land (BR465).
- Deleterious materials.
- Ground conditions.
- Hazardous substances.
- Mould growth.
- Radon.
- Radon: Guidance on protective measures for new buildings BR 211.
- Types of damp-proof courses.
Featured articles and news
The Building Safety Forum at the Installershow 2025
With speakers confirmed for 24 June as part of Building Safety Week.
The UK’s largest air pollution campaign.
Future Homes Standard, now includes solar, but what else?
Will the new standard, due to in the Autumn, go far enough in terms of performance ?
BSRIA Briefing: Cleaner Air, Better tomorrow
A look back at issues relating to inside and outside air quality, discussed during the BSRIA briefing in 2023.
Restoring Abbotsford's hothouse
Bringing the writer Walter Scott's garden to life.
Reflections on the spending review with CIAT.
Retired firefighter cycles world to raise Grenfell funds
Leaving on 14 June 2025 Stephen will raise money for youth and schools through the Grenfell Foundation.
Key points for construction at a glance with industry reactions.
Functionality, visibility and sustainability
The simpler approach to specification.
Architects, architecture, buildings, and inspiration in film
The close ties between makers and the movies, with our long list of suggested viewing.
SELECT three-point plan for action issued to MSPs
Call for Scottish regulation, green skills and recognition of electrotechnical industry as part of a manifesto for Scottish Parliamentary elections.
UCEM becomes the University of the Built Environment
Major milestone in its 106-year history, follows recent merger with London School of Architecture (LSE).
Professional practical experience for Architects in training
The long process to transform the nature of education and professional practical experience in the Architecture profession following recent reports.
A people-first approach to retrofit
Moving away from the destructive paradigm of fabric-first.
International Electrician Day, 10 June 2025
Celebrating the role of electrical engineers from André-Marie Amperè, today and for the future.
New guide for clients launched at Houses of Parliament
'There has never been a more important time for clients to step up and ...ask the right questions'
The impact of recycled slate tiles
Innovation across the decades.
EPC changes for existing buildings
Changes and their context as the new RdSAP methodology comes into use from 15 June.