Compression
Contents |
[edit] Simple compression
Simple compression occurs when the particles of a material are pushed against each other. As a state of stress, it is the opposite of tension, where particles are pulled apart.
When a column supports a load (or weight) from above, it is said to be under compressive stress; it also shortens – a typical consequence of compression. The same applies to a strut in a truss or bridge which is designed to work solely in compression.
Compressive shortening is proportional to the load per unit area (of a column) and is typical of compression, just as lengthening is typical of tension. In addition to the compressive shortening which takes place along the longitudinal axis (usually the centre line), there is also lengthening that occurs at right angles to the longitudinal axis. In other words, the column gets shorter and fatter.
Strictly speaking, a compression member such as a column or strut is subject only to axial compressive forces ie the load is applied through the member’s centre and along the longitudinal axis. The stress in the compressed member is given by the load over the cross-sectional area.
Simple compression is a common phenomenon in building structures as all loads and forces have eventually to be directed into the ground. Thus, they occur in Greek temples as much as in Manhattan skyscrapers.
[edit] Strength of materials
Concrete, masonry are materials with high compressive strengths but they are also weak in resisting tension. Steel has a high compressive strength and also a high tensile strength and can resist the same compressive forces as concrete or masonry but with a slimmer profile.
[edit] Buckling
When a material has sufficient compressive strength to allow the use of smaller cross-sections, the result may be lower costs but this could have side effects. Increasing the slenderness ratio (the column length is many times greater compared to the cross-sectional area), may lead to buckling. If the load is great combined with a relatively small cross-sectional area, the column may buckle as it is easier for it to bend outwards (or buckle), rather than shorten. Buckling may also be exacerbated by eccentric loads.
Whether a column reaches its buckling load limit will depend on numerous factors, including its length, the type of material, the cross-sectional shape and how it is restrained at its ends.
[edit] Compressive structures
Being built mostly from masonry, Greek and Roman temples, and Romanesque and Gothic cathedrals, are structures almost entirely under compression.
An arch in brickwork or stonework has simple, uniform compression and no bending (and therefore little or no tension). The thrust of the arch – compressive forces diverging down and either side of the keystone – is absorbed by the abutments on either side. For more information see: Arch
The flying buttress in a Gothic cathedral channels forces of compression from the roof and walls down into the foundations. For more information see: Flying buttress
When under load, a dome develops compressive stresses along its meridians; these can be thought of as an infinite number of arches connecting opposite points on the ground circumference. The dome will also develop compressive or tensile stresses around its hoops (lines of ‘latitude’). For more information see: Dome
[edit] Related articles on Designing Buildings
- Arch.
- Barrel vault.
- Concrete.
- Dome.
- Elements of structure in buildings
- Engineer.
- Flying buttress.
- Shear strength.
- Steel.
- Stress.
- Structural engineer.
- Structural principles.
- Strut.
- Substructure.
- Superstructure.
- Tensile strength.
- Tension.
- Ties.
- Tower.
- Types of structure.
- Vibration Compaction Technology.
- Voussoir.
Featured articles and news
International Electrician Day, 10 June 2025
Celebrating the role of electrical engineers from André-Marie Amperè, today and for the future.
New guide for clients launched at Houses of Parliament
'There has never been a more important time for clients to step up and ...ask the right questions'
The impact of recycled slate tiles
Innovation across the decades.
EPC changes for existing buildings
Changes and their context as the new RdSAP methodology comes into use from 15 June.
Skills England publishes Sector skills needs assessments
Priority areas relating to the built environment highlighted and described in brief.
BSRIA HVAC Market Watch - May 2025 Edition
Heat Pump Market Outlook: Policy, Performance & Refrigerant Trends for 2025–2028.
Committing to EDI in construction with CIOB
Built Environment professional bodies deepen commitment to EDI with two new signatories: CIAT and CICES.
Government Grenfell progress report at a glance
Line by line recomendation overview, with links to more details.
An engaging and lively review of his professional life.
Sustainable heating for listed buildings
A problem that needs to be approached intelligently.
50th Golden anniversary ECA Edmundson apprentice award
Deadline for entries has been extended to Friday 27 June, so don't miss out!
CIAT at the London Festival of Architecture
Designing for Everyone: Breaking Barriers in Inclusive Architecture.
Mixed reactions to apprenticeship and skills reform 2025
A 'welcome shift' for some and a 'backwards step' for others.
Licensing construction in the UK
As the latest report and proposal to licence builders reaches Parliament.
Building Safety Alliance golden thread guidance
Extensive excel checklist of information with guidance document freely accessible.
Fair Payment Code and other payment initiatives
For fair and late payments, need to work together to add value.
Pre-planning delivery programmes and delay penalties
Proposed for housebuilders in government reform: Speeding Up Build Out.
High street health: converting a building for healthcare uses
The benefits of health centres acting as new anchor sites in the high street.