Understanding Cooling and Heating Loads
Contents |
[edit] Introduction
As a knowledgeable professional in the HVAC industry, it’s crucial to provide accurate advice to designers, not only to improve your own credibility but also to enhance their projects and potentially secure more orders. To facilitate this process, we have compiled a set of rules of thumb that can be applied to most general applications. However, it’s imperative to emphasise that while we are well-versed in HVAC principles, we are not designers, and our advice should always be verified by others before installation. This disclaimer must be clearly stated in all written communications if our equipment design is based on these rules of thumb.
[edit] Cooling Loads
When considering cooling loads, a general guideline is to allocate 120 – 160 watts per square meter, taking into account factors such as solar gain, people, and lighting. Alternatively, you can estimate the cooling requirement at 1 kilowatt per occupant. Additionally, for each meter per second of fresh air introduced, add approximately 10 kilowatts to the total cooling load. If a designer provides the desired cooling load in kilowatts, a quick crosscheck can be performed using the rule of thumb that suggests a maximum of 20 kilowatts per cubic meter of air. Any value surpassing this threshold will likely necessitate an increase in air volume.
To calculate the cooling load using psychometric charts, the following equation can be applied: Cooling Load (kW) = Enthalpy Difference (total heat content) x Air Volume Specific Volume (m³/kg) at the entering condition
For example, consider the following data: Air Volume: 1.5 m³/s Entering Air Temperature (EAT): 28°C dry bulb / 50% relative humidity (Specific Enthalpy: 59 kJ/kg) Leaving Air Temperature (LAT): 12°C dry bulb / 11.5°C wet bulb (Specific Enthalpy: 33 kJ/kg)
Using the equation, the calculation would be as follows: Cooling Load (kW) = (59 – 33) x 1.5 m³/s / 0.869 m³/kg Therefore, the cooling load amounts to 44.88 kW.
[edit] Heating Loads
For heating loads, a general rule of thumb suggests allocating 45 watts per cubic meter, considering the volume of the space. Additionally, when accounting for fresh air load, a standard equation can be used: kW = AT°C × 1.207 (constant) × M.
It’s important to note that this guideline is applicable when heating the building using the Air Handling Unit (AHU). In cases where heating is provided through alternative means, such as radiators, the equation kW = OT°C × 1.207 × M should be employed for tempered ventilation.
[edit] Conclusion
By utilising these rules of thumb, HVAC professionals can assist designers in estimating cooling and heating loads for various applications. However, it is crucial to emphasise that these guidelines serve as initial estimations and should be verified by qualified designers to ensure accuracy and compliance with specific project requirements. Clear communication about our role, lack of design liability insurance, and the need for independent design verification should be included in all written correspondences. By adhering to these principles, we can enhance our credibility, improve collaboration with designers, and deliver superior HVAC solutions.
--Building Ventilation Solutions
[edit] Related articles on Designing Buildings
- Air conditioning.
- Air handling unit.
- Approved Document F.
- Building services
- Building services engineer.
- Condensation.
- Dehumidification.
- Displacement ventilation.
- Ductwork.
- Dehumidification.
- Dry-bulb temperature.
- Fan coil unit.
- Heating.
- Humidification.
- HVACR.
- Humidification.
- Humidistat.
- HVAC.
- Interstitial condensation.
- Mechanical, electrical and plumbing MEP.
- Mechanical ventilation.
- Moisture content.
- Natural ventilation.
- Plant room.
- Psychometric chart.
- Refrigeration.
- Sling psychrometer.
- Thermal comfort.
- Thermal indices.
- Ventilation.
- Water vapour.
- Wet-bulb temperature.
[edit] External links
Other articles by author Simon Windsor https://www.bvs-ltd.co.uk/author/simon/
Featured articles and news
Key documents that represent an early shift in thinking.
A resource for Cleaner Air, Better Tomorrow.
Awe-inspiring medieval great barns.
A history of timber construction in the UK
From a timber Stonehenge to half timber houses.
Registered building inspectors
Building types and conflicts of interest updates explaineed.
Engineering services still struggle with labour shortages
According to latest quarterly services survey of the sector.
Infrastructure that connect the physical and digital domains.
Harnessing robotics and AI in challenging environments
The key to nuclear decommissioning and fusion engineering.
BSRIA announces Lisa Ashworth as new CEO
Tasked with furthering BSRIA’s impressive growth ambitions.
Public buildings get half a million energy efficiency boost
£557 million to switch to cleaner heating and save on energy.
CIOB launches pre-election manifesto
Outlining potential future policies for the next government.
Grenfell Tower Inquiry announcement
Phase 2 hearings come to a close and the final report due in September.
Progress from Parts L, F and O: A whitepaper, one year on.
A replicated study to understand the opinion of practitioners.
ECA announces new president 2024
Electrical engineer and business leader Stuart Smith.
A distinct type of countryside that should be celebrated.
Comments
[edit] To make a comment about this article, click 'Add a comment' above. Separate your comments from any existing comments by inserting a horizontal line.
Thanks for a useful article. Did you know you can set up a profile for your company, with details, logo and website. If you associate the article to that profile, then the company profile will appear at the top of the article.
Other forms of marketing within an article will normally be deleted. Find out more on this page https://www.designingbuildings.co.uk/wiki/Create_a_new_article