Notation and units on drawings and documents
Contents |
[edit] Introduction
The same notation conventions should be followed by all so that there is clear communication between different people and mistakes are avoided.
[edit] Decimal marker
The decimal marker (full stop) on the baseline is the standard decimal point in the UK; but the marker at the halfway position is also acceptable, e.g. 1.618 or 1·618. It should be noted that Continental practice is to use the comma on the baseline, e.g. 1,618.
When the value to be expressed is less than unity it should be preceded by zero (e.g. 0.6 not .6). Whole numbers may be expressed without a decimal marker, but it is also wise to add the marker to avoid misunderstandings, e.g. 6.0. The appropriate number of decimal places should be chosen depending on the circumstances in which the resulting value is to be used.
[edit] The thousand marker
To avoid confusion with the Continental decimal marker, no thousand marker (comma) should be used. Where legibility needs to be improved a space can be left in large groups of digits at every thousand point. Where there are only four digits, a space between the first digit and the others is not desirable (e.g. 15 000, 1500). However, the comma is used in currency, e.g. £115,000.
[edit] Multiplication sign
It is common for the letter 'x' to be used in place of the multiplication sign. This is considered incorrect in mathematical writing. In the algebraic notation, a multiplication symbol is usually omitted wherever it may cause confusion: 'a multiplied by b' can be written as ab or a' b.
On Microsoft Windows computers, holding the [Alt] key and typing the number 0215 on the number pad (right hand number keys on the keyboard, not the top row numbers) will produce the multiplication symbol (×) for you.
[edit] Units
The main units that should be used are as shown in table below.
The same unit symbol, i.e. m, mm, kg, should be used for singular and plural values (1 kg, 10 kg), and no full stops or any other punctuation marks should be used after the symbol, unless it occurs at the end of a sentence.
Use a ‘solidus’ or sloping line as a separator between a numerator and a denominator, i.e. 3 kg/m³ or 3 kg/cu m (Mass per unit volume - SI derived unit of density).
A single space should separate figures from unit symbols: 10 m, not 10m.
The unit should be written in full if there is any doubt about the unit symbol. For example, the recognised unit unit symbol l for the unit litre can be confused with the number 1, therefore it is less confusing to write litre in full. Also, the unit symbol t for tonne may in some circumstances be confused with the imperial ton, so in this instance the unit tonne should then be written in full as well.
When unit symbols are raised to various powers, it is only the unit symbol which is involved and to the number attached to it. Thus, 3 m³ equals 3 (m)³ and not 3 m × 3 m × 3 m (i.e. the answers is 3 cubic metres not 27 cubic metres).
Difficulty may be experienced when reproducing the squaring and cubing indices for m or mm, and m³ or mm³. In such cases, units may be written with the indices on the line instead of the superscripts (m2, m3). Alternatively, and probably for the best, particularly when the general public is involved, the abbreviation ‘sq’ and ‘cu’ should be used (e.g. sq m and cu m).
Units should not be hyphenated (milli-metres)
[edit] Notation
As a rule, the sizes of components should be expressed consistently and not in mixed units, e.g. 1500 mm × 600 mm × 25 mm thick and not 1.5 m × 60cm × 25 mm thick. However, for long thin components such as timbers, it is acceptable to mix the units, e.g. 100 mm × 65 mm × 10 m long, but to avoid confusion and mistakes try to keep to the same units.
It is important to distinguish clearly between the metric tonne and the imperial ton.
- The metric tonne (1,000 kilograms) is equivalent to 2204.623 lb
- The UK imperial long ton (1016.047 kilograms) equals to 2240 lb
- The US imperial short ton (907.1847 kilograms) equals 2000 lb
The interval of temperature should be referred to as degree Celsius (°C) and not as centigrade. The word centigrade is used by Continental metric countries as a measure of plane angle and equals 1/10 000th part of a right angle.
[edit] Superscript and subscript
Where appropriate superscript and subscript text is not available, the following notations may be used instead:
- ^ to indicate superscript text, and ^() if there is more than one character.
- Underscore _ to indicate subscript text, and _() if there is more than one character.
[edit] Related articles on Designing Buildings Wiki
- Archidict.
- Brand guidelines.
- Common spelling mistakes in the construction industry.
- Concept drawing.
- Cubic metre.
- Drawings.
- Elevations.
- Manual drafting techniques.
- Metric system.
- Paper sizes.
- Schematic.
- Shop drawing.
- Specification.
- Symbols on architectural drawings.
- Technical drawing pen sizes.
- Units.
- Working drawing.
- Writing technique.
- Visualisation.
Featured articles and news
The UK's Modern Industrial Strategy: A 10 year plan
Previous consultation criticism, current key elements and general support with some persisting reservations.
Building Safety Regulator reforms
New roles, new staff and a new fast track service pave the way for a single construction regulator.
Architectural Technologist CPDs and Communications
CIAT CPD… and how you can do it!
Cooling centres and cool spaces
Managing extreme heat in cities by directing the public to places for heat stress relief and water sources.
Winter gardens: A brief history and warm variations
Extending the season with glass in different forms and terms.
Restoring Great Yarmouth's Winter Gardens
Transforming one of the least sustainable constructions imaginable.
Construction Skills Mission Board launch sector drive
Newly formed government and industry collaboration set strategy for recruiting an additional 100,000 construction workers a year.
New Architects Code comes into effect in September 2025
ARB Architects Code of Conduct and Practice available with ongoing consultation regarding guidance.
Welsh Skills Body (Medr) launches ambitious plan
The new skills body brings together funding and regulation of tertiary education and research for the devolved nation.
Paul Gandy FCIOB announced as next CIOB President
Former Tilbury Douglas CEO takes helm.
UK Infrastructure: A 10 Year Strategy. In brief with reactions
With the National Infrastructure and Service Transformation Authority (NISTA).
Ebenezer Howard: inventor of the garden city. Book review.
The Grenfell Tower fire, eight years on
A time to pause and reflect as Dubai tower block fire reported just before anniversary.
Airtightness Topic Guide BSRIA TG 27/2025
Explaining the basics of airtightness, what it is, why it's important, when it's required and how it's carried out.
Construction contract awards hit lowest point of 2025
Plummeting for second consecutive month, intensifying concerns for housing and infrastructure goals.
Understanding Mental Health in the Built Environment 2025
Examining the state of mental health in construction, shedding light on levels of stress, anxiety and depression.
The benefits of engaging with insulation manufacturers
When considering ground floor constructions.
Lighting Industry endorses Blueprint for Electrification
The Lighting Industry Association fully supports the ECA Blueprint as a timely, urgent call to action.