Concrete compaction
Contents |
[edit] Introduction
Compaction is a process of expelling entrapped air. If we don’t expel this air, it will result into honeycombing and reduced strength. It has been found from the experimental studies that 1% air in concrete reduces the strength by approximately 6%.
There are two methods of compaction:
- Hand compaction.
- Mechanical compaction i.e vibration method
- Compaction by pressure and jolting method
- Compaction by a spinning method
[edit] Hand compaction
Hand compaction is used for simple, small structures. Workability should be decided in such a way that the chances of honeycombing is minimised.
Methods of hand compaction include:
- Rodding: 'Poking' with a 2m long, 16 mm dia rod at sharp corners and edges. The thickness of layers for rodding should be 15 to 20 cm.
- Ramming: Generally used for compaction on ground in plain concrete. It is not used either in RCC or on upper floors.
- Tamping: The top surface is beaten by a wooden cross beam of cross section 10 cm x 10 cm. Both compaction and levelling are achieved simultaneously. It is mainly used for roof slabs and road pavements.
[edit] Mechanical compation
Vibration is imparted to the concrete by mechanical means. This causes temporary liquefaction so that air bubbles come to the top and are expelled.
Mechanical vibration techniques include:
- Internal vibration: The most commonly used technique of concrete vibration. Vibration is achieved by eccentric weights attached to a shaft. The needle diameter varies from 20 mm to 75 mm and its length varies from 25 cm to 90 cm. The frequency range adopted is normally 3500 to 5000 rpm.
- External vibration: This is adopted where internal vibration can’t be used due to either thin sections or heavy reinforcement. External vibration is less effective and it consumes more power compared to the internal vibration. The formwork also has to be made extra strong when external vibration is used.
- Table vibration: Mainly used for laboratories where concrete is put on the table.
- Platform vibration: Similar to table vibrators but these are generally used on a very large scale.
- Surface vibration: These are also called screed board vibrators. The action is similar to that of tamping. The vibrator is placed on screed board and vibration is given on the surface. It is mainly used for roof slabs, road pavements etc., but it is not effective beyond 15 cm depth.
[edit] Compaction by pressure and jolting method
- In this method, stiff concrete is subjected to external pressure from the top and vibration from the bottom along with a series of jolting actions
- Excess water added during mixing exits due to large pressure
[edit] Compaction by a spinning method
- Compaction by Spinning is also called centrifugation
- This method Compaction by Spinning is used in the manufacture of concrete pipes, concrete lamp posts etc
- The initial w/c ratio of 0.35 to 0.40 reduced to about 0.30 after spinning
[edit] Related articles on Designing Buildings Wiki.
- 3D concrete printer.
- Architectural concrete.
- Cast-in-place concrete.
- Cellular concrete.
- Concrete.
- Concrete in aggressive ground (SD 1).
- Concrete-steel composite structures.
- Concreting plant.
- Precast concrete.
- Prestressed concrete.
- Power float.
- Reinforced concrete.
- Scabbling.
- Self-compacting concrete.
- Stratification of concrete.
- Testing concrete.
- The properties of concrete.
- source Civil Experience
Featured articles and news
BSRIA Sentinel Clerk of Works Training Case Study
Strengthening expertise to enhance service delivery with integrated cutting-edge industry knowledge.
Impact report from the Supply Chain Sustainability School
Free sustainability skills, training and support delivered to thousands of UK companies to help cut carbon.
The Building Safety Forum at the Installershow 2025
With speakers confirmed for 24 June as part of Building Safety Week.
The UK’s largest air pollution campaign.
Future Homes Standard, now includes solar, but what else?
Will the new standard, due to in the Autumn, go far enough in terms of performance ?
BSRIA Briefing: Cleaner Air, Better tomorrow
A look back at issues relating to inside and outside air quality, discussed during the BSRIA briefing in 2023.
Restoring Abbotsford's hothouse
Bringing the writer Walter Scott's garden to life.
Reflections on the spending review with CIAT.
Retired firefighter cycles world to raise Grenfell funds
Leaving on 14 June 2025 Stephen will raise money for youth and schools through the Grenfell Foundation.
Key points for construction at a glance with industry reactions.
Functionality, visibility and sustainability
The simpler approach to specification.
Architects, architecture, buildings, and inspiration in film
The close ties between makers and the movies, with our long list of suggested viewing.
SELECT three-point plan for action issued to MSPs
Call for Scottish regulation, green skills and recognition of electrotechnical industry as part of a manifesto for Scottish Parliamentary elections.
UCEM becomes the University of the Built Environment
Major milestone in its 106-year history, follows recent merger with London School of Architecture (LSE).
Professional practical experience for Architects in training
The long process to transform the nature of education and professional practical experience in the Architecture profession following recent reports.
A people-first approach to retrofit
Moving away from the destructive paradigm of fabric-first.
New guide for clients launched at Houses of Parliament
'There has never been a more important time for clients to step up and ...ask the right questions'
The impact of recycled slate tiles
Innovation across the decades.
EPC changes for existing buildings
Changes and their context as the new RdSAP methodology comes into use from 15 June.