Compressive strength
Materials used for structural purposes are usually classified according to their resistance to basic stresses such as compression, tension and shear.
Compression is a force that pushes the particles of a material closer together. For example, when a column supports a load, it is under compression and its height shortens, albeit often imperceivably. The opposite is tensile force which tends to elongate a material.
All materials can, to a certain degree, withstand compressive forces before they fail and it is at this point that compressive strength is measured. Therefore, the compressive strength of a material is usually stated as the maximum compression that the material can stand before failure.
Materials which can resist high, applied compressive forces before failure are said to have high compressive strengths.
Some materials are better than others at withstanding compression before failure occurs. Steel can withstand relatively high compressive forces. Other materials, such as concrete and ceramics, typically show much higher compressive strengths than tensile strengths. Depending on the material, failure can comprise fracture at the compressive strength limit or irreversible deformation.
[edit] Measuring compressive strength
It is possible to measure precisely the compressive strength of materials by conducting a compressive test under carefully controlled conditions using a universal testing machine. This can typically have testing capacities of up to 53 mega Newtons (MN) which is equal to a 5,404 ton force.
In building construction, testing the compressive strength of concrete is usually undertaken at different stages after it has been poured in order to allow sufficient time for strength development (eg after 28 days). Typically, a cube (or cylinder) of concrete is used as a test specimen, ensuring that the top and bottom surfaces are flat and parallel, and that both faces are a perfect cross-section, ie, at right angles to the vertical axis of the cube.
A compressive force is applied to the specimen gradually by the testing mechanism. Measuring the compressive strength using this method requires:
- The cross-sectional area of one of the cube’s faces, top or bottom (they should be identical), and
- The compressive force applied at the time of failure (defined as permanent deformation - ie an inability to assume its former shape once the compressive force is removed).
Once these measurements are available, the compressive strength (C or σc) can be calculated as:
[edit] C = F/A
where F is the maximum force (load) applied at the point of failure and A is the cross-sectional area of the specimen before the force was applied. It can be expressed in terms of N/m² or Pascals (where 1 Pascal (Pa) = 1 N/m²).
It is sometimes difficult to measure the compressive strength of ductile metals, such as mild steel, which have high compressive strengths. This is due to the failure mode of such materials. Typically, under a compressive load, mild steel deforms elastically up to a point; this is followed by plastic deformation and ultimately the specimen may be flattened without significant evidence of fracture. It can therefore be difficult to measure the precise point of compressive failure. For this reason, it is more common to quote the tensile strength of mild steel which is easier to obtain; as its tensile strength is always lower than its compressive strength, it can be used as the basis for calculations.
[edit] Related articles on Designing Buildings
- Arch.
- Barrel vault.
- Compressive strength of timber lattice columns for low-rise construction.
- Concrete.
- Dome.
- Elements of structure in buildings
- Engineer.
- Flying buttress.
- Mass concrete.
- Steel.
- Structural engineer.
- Structural principles.
- Substructure.
- Superstructure.
- Tower.
- Tensile strength.
- Tension.
- Types of structure.
- Voussoir.
Featured articles and news
The 5 elements of seiri, seiton, seiso, seiketsu and shitsuke.
Shading for housing, a design guide
A look back at embedding a new culture of shading.
The Architectural Technology Awards
The AT Awards 2025 are open for entries!
ECA Blueprint for Electrification
The 'mosaic of interconnected challenges' and how to deliver the UK’s Transition to Clean Power.
Grenfell Tower Principal Contractor Award notice
Tower repair and maintenance contractor announced as demolition contractor.
Passivhaus social homes benefit from heat pump service
Sixteen new homes designed and built to achieve Passivhaus constructed in Dumfries & Galloway.
CABE Publishes Results of 2025 Building Control Survey
Concern over lack of understanding of how roles have changed since the introduction of the BSA 2022.
British Architectural Sculpture 1851-1951
A rich heritage of decorative and figurative sculpture. Book review.
A programme to tackle the lack of diversity.
Independent Building Control review panel
Five members of the newly established, Grenfell Tower Inquiry recommended, panel appointed.
Welsh Recharging Electrical Skills Charter progresses
ECA progressing on the ‘asks’ of the Recharging Electrical Skills Charter at the Senedd in Wales.
A brief history from 1890s to 2020s.
CIOB and CORBON combine forces
To elevate professional standards in Nigeria’s construction industry.
Amendment to the GB Energy Bill welcomed by ECA
Move prevents nationally-owned energy company from investing in solar panels produced by modern slavery.
Gregor Harvie argues that AI is state-sanctioned theft of IP.
Experimental AI housing target help for councils
Experimental AI could help councils meet housing targets by digitising records.
BSRIA Occupant Wellbeing survey BOW
Occupant satisfaction and wellbeing tool inc. physical environment, indoor facilities, functionality and accessibility.