Power over USB
The Universal Serial Bus (USB) is designed to provide power as well as data communications. It can support 127 devices and has developed over the years from 1.5 Mb/s to 480 Mb/s. Currently (2014) a normal USB 2.0 has a low current limit of 100 mA and a high current limit of 500 mA at 5 V although a Thunderbolt connector is able to deliver 2 A at 5 V. Several years ago USB 3.0 was introduced which increased the theoretical bit rate by 10x’s to 5 Gb/s and raised the low current limit to 150 mA and the high current limit to 900 mA. More recently the USB 3.0 Promoter Group has announced a new specification which will allow USB 3.0 compatible sockets and cables to deliver up to 100 W by changing the voltage from 5 V to 20 V and increasing the current to 5 A.
USB also has limitations on the maximum cable length and in most cases this is restricted to 3m. With special cables this can be increased to over 6 m and with a USB bridge this can be extended to over 30 m. With such a large increase in power a single USB 3 SuperSpeed hub could be charging a laptop, powering an external hard drive as well as a second monitor. In future, TV manufacturers could include high-powered USB hubs to power nearby AV and communication equipment thereby reducing the need for multiple wall outlets.
Both USB and PoE (power over ethernet) bring power and communication functions together by using the data exchange capabilities to negotiate power need with the device in a number of incremental stages. This level of power control allows a common supply to deliver a range of different power profiles best suited to whichever device is connected to that particular port. For example, in the future a USB 3 might provide 60 W (20 V at 3 A) for a laptop or 5 to 10 W (5 V at 1 or 2 A) for an average smart phone.
The benefit of both of these systems is that they are well developed solutions that are supported by appropriate standards, research and testing. Components are readily available and system design expertise is relatively common.
In terms of network distribution efficiency both PoE and USB are still subject to conversion and distribution losses as any other network. Whilst a modern PoE injector may have a very efficient power supply, power is still converted from 230 V AC to approximately 50 V DC, distributed to the point-of-load and then converted again to what’s required by the end device. In the case of PoE the voltage is higher than USB potentially reducing its distribution losses although conductor sizes are relatively small.
In the domestic environment USB ports are much more common and could in the future be used not just for connecting between devices, for example a laptop and a peripheral, but also as an additional low voltage power outlet complimenting the existing 230 V wall outlet. This may reduce the need for individual power adapters and bulky 230 V plugs and sockets although where this is the case, USB sockets are still likely to be associated with a central device such as a TV or computer.
This article was created by --BRE. It was taken from The future of electricity in domestic buildings, a review, by Andrew Williams, published in November 2014.
[edit] Related articles on Designing Buildings Wiki
Featured articles and news
Tackling the lack of knowledge or confidence in heat pumps
The CICV Green Home Festival part of the Edinburgh Fringe.
Home improvements swapped for green energy upgrades
As applications down since and desire to reduce bills up.
Eco apprenticeships continue help grow green workforce
A year after being recognised at the King's coronation.
The Use of Natural Insulation Materials in Retrofit
New paper from STBA with support from SDF.
National Retrofit Hub in partnership with InstallerSHOW.
Permitted development rights for agricultural buildings
The changes coming into effect as of May 21, 2024.
Biodiversity and the built environment digital series
The nature of building, with CIOB and CWP.
A call for prevention and sensitive re-use.
Risks to the long-term effectiveness of the BNG scheme
National Audit Office publish review of Biodiversity Net Gain.
The CIAT principal designer register
Providing assurance and verification of the capability and competence of registered ATs.
Building Safety recommendations and Northern Ireland
The NI roadmap to improving safety in high rise residential.
Specifying rendered external wall insulation for fire safety
How to interrogate the evidence provided to the specifier.
The benefits of writing articles for your organisation
How to create a profile for your organisation and publish for free.
No Falls Week. The importance of safe working at height
What to expect and what is on offer to avoid accidents.
Scottish Government action to reach net-zero targets
Retrofit expert group highlight critical actions needed.
A forward thinking, inclusive global community of members.