Designing Buildings - User contributions [en]

Solar gain in buildings

2019-10-18T09:35:37Z

The Window Film Company:

Solar gain is short wave radiation from the sun that heats a building, either directly through an opening such as a window, or indirectly through the fabric of the building. Solar design (or passive solar design) is an aspect of passive building design that focusses on maximising the use of heat energy from solar radiation.

Solar gain is a particularly effective form of passive heating as radiation from the sun is predominately short-wave infrared radiation which is able to pass through glazing and heat the internal fabric of the building. The long-wave infrared radiation that is re-radiated by the heated fabric of the building is not able to pass back out through the glazing. This results in heat accumulating in the interior, sometimes referred to as the 'greenhouse effect'. See Thermal optical properties for more information.

Very broadly, solar gain can be beneficial in cooler climates when it can be used as a passive way of heating buildings. However, too much solar gain can cause overheating and for this reason, Part L of the UK building regulations places restrictions on the amount of glazing that can be used in buildings. Overheating as a result of solar gains can be a particular problem in warmer climates. However, the situation is complicated by the variation in conditions throughout the day and year which can mean that solar gain can be beneficial in the morning and evening, or during the winter, but can be problematic during the middle of the day or in the summer.

Relatively straight-forward design solutions such as brise soleil can be used to allow low-level winter sun to enter a building, but to shade higher, summer sun. Other solutions, such as planting deciduous trees in front of windows can be effective as leaf cover in the summer will shade glazing from solar radiation, whereas in the winter sunlight is able to pass between the bare branches and enter the building.

[[File:Passive_design.jpg|link=File:Passive_design.jpg]][Image: Passive design]

Thermal mass in the building's interior can be used to even out variations in solar radiation, storing gains accumulated during the middle of the day and releasing them slowly, providing an ongoing heat source during cooler times of the day. An example of the use of thermal mass is a trombe wall, illustrated below.

[[File:Trombe_wall.jpg|link=File:Trombe_wall.jpg]][Image: Trombe wall]

Low-e coatings on glazing can also increase the retention of solar gains by increasing the proportion of re-radiated long-wave infrared radiation that is reflected back into the interior. This effect can be enhanced at night by the use of curtains or shutters.

Maximising the benefits of solar gains can be complex and requires consideration of a wide range of issues:

* Location.
* Landscape.
* Orientation.
* Massing.
* Shading.
* Thermal mass.
* Insulation.
* Internal layout.
* The positioning of openings.
* The thermal optical properties of openings.
* The thermal properties of the building envelope.

In large or complex buildings, optimising solar gains can be require a great deal of analysis, and may involve the use of techniques such as computational fluid dynamics to model the distribution of heat through the building. Design solutions such as solar chimneys can drive the entire design of the building, its heating strategy and ventilation strategy.

[[File:Solar_chimney.jpg|link=File:Solar_chimney.jpg]][Image: Solar chimney]

Solar heat gain can be reduced by:

* Horizontal shading.
* Limiting the area of openings.
* Orientating openings away from the sun path.
* Adding solar reflective [https://www.windowfilm.co.uk/commercial/heat heat rejection window film] to new or existing glazing.
* Reducing solar transmittance through openings, for example by reflective glazing. This might be used in conjunction with low-e coatings that reduce the long-wave solar radiation transmitted from the outside to the inside.
* Purging heat gains by the introduction of ventilation.
* Insulating the building envelope to prevent the transmission of indirect solar gains.
* Reducing the solar absorptance of the building envelope. The term 'albedo' relates to the total reflectance of a specific system. White coloured surfaces can be effective in minimising heat transfer into buildings.
* Reducing the urban heat island effect.
* Planting to provide shading and to reduce the solar absorption of roofs. See Green roofs for more information.

NB: Solar radiation can also be used to provide heat to buildings through the use of solar thermal panels and solar photovoltaics.

= Find out more =

=== Related articles on Designing Buildings Wiki ===

* Albedo.
* Brise soleil.
* Building fabric.
* Cool roofs.
* Emissivity.
* G-value.
* Large scale solar thermal energy.
* Low-e glass.
* Natural ventilation.
* Part L.
* Passive building design.
* Shading coefficient.
* Solar chimney.
* Solar heat gain coefficient.
* Solar photovoltaics.
* Solar shading.
* Solar thermal panels.
* Thermal comfort.
* Thermal mass
* Thermal optical properties.
* Trombe wall.
* Urban heat island effect.
* Visible light.

[[Category:Sustainability]]

Glass manifestation

2019-10-18T09:15:03Z

The Window Film Company:

[[File:Manifest1.jpg|link=File:Manifest1.jpg]]

[https://www.windowfilm.co.uk/commercial/manifestation Manifestation] is a treatment that can be applied to glass windows, doors, partitions and any other large expanses of clear glass, in order to make the glass visible, preventing injury through collisions. It can also help enhance privacy and can be decorative.

Manifestation is typically created from a [https://www.windowfilm.co.uk/frosted-window-film frosted film] applied at specified locations on clear glass to make it more easy to detect.

Building regulations requirement K5.2: Manifestation of glazing, states that:

{|
| Transparent glazing with which people are likely to come into contact while moving around in or about the building, shall incorporate features which make it apparent.
|}

Approved document K, Protection from falling, collision and impact, suggests that this requirement will be satisfied by including permanent means of indicating the presence of large uninterrupted areas of transparent glazing, and Section 7 of the approved document provides further details, requiring that either:

{|
|width="100%"| They are clearly defined with glass manifestation on the glass at two levels; between 850-1,000 mm and 1,400-1,600 mm above the floor, contrasting visually with the background seen through the glass (both inside and out) in all lighting conditions. Manifestation takes the form of logo or sign at least 150 mm high (repeated if on a glazed screen), or a decorative feature such as broken lines or continuous bands, at least 50 mm high.
|}

[[File:Manifestation_specification.jpg|link=File:Manifestation_specification.jpg]]

The most simple manifestation is two rows of 50-75 mm white or frosted dots, however, the regulations do not dictate the appearance of the manifestation. Standard designs of dots, squares and simple bands are common, but large panels in etched or printed film with cut-out clear spaces, or [https://www.windowfilm.co.uk/graphics/glass-manifestation branded manifestation with logos] or other designs are also acceptable.

Alternative solutions such as mullions, transoms, door frames or large pull handles / push plates may also be acceptable.

In addition, doors should be apparent from the side, if they can be held open, and where glazed doors are beside a glazed screen, they should be marked with a high contrast strip along the top and at both sides.

[https://www.windowfilm.co.uk/graphics/manifestation-legislation Glass Manifestation Regulations & Legislation]<br />
The approved document to Part M of the Building Regulations - access to and use of buildings - states that people with visual impairment should be in no doubt as to the location of glass doors and screens, and steps should be taken to avoid people being harmed by walking into them. This requirement is satisfied if they comply with approved document K, section 7.

= Find out more =

=== Related articles on Designing Buildings Wiki ===

* BFRC window rating scheme.
* Curved glass.
* Doors.
* Glass.
* Glass block flooring.
* Glazing.
* Low-E glass.
* Patent glazing.
* Security glazing.
* Types of window.

[[Category:Health_and_safety_/_CDM]] [[Category:Products_/_components]]

Glass manifestation

2019-10-18T09:12:26Z

The Window Film Company:

[[File:Manifest1.jpg|link=File:Manifest1.jpg]]

[https://www.windowfilm.co.uk/commercial/manifestation Manifestation] is a treatment that can be applied to glass windows, doors, partitions and any other large expanses of clear glass, in order to make the glass visible, preventing injury through collisions. It can also help enhance privacy and can be decorative.

Manifestation is typically created from a [https://www.windowfilm.co.uk/frosted-window-film frosted film] applied at specified locations on clear glass to make it more easy to detect.

Building regulations requirement K5.2: Manifestation of glazing, states that:

{|
| Transparent glazing with which people are likely to come into contact while moving around in or about the building, shall incorporate features which make it apparent.
|}

Approved document K, Protection from falling, collision and impact, suggests that this requirement will be satisfied by including permanent means of indicating the presence of large uninterrupted areas of transparent glazing, and Section 7 of the approved document provides further details, requiring that either:

{|
|width="100%"|
They are clearly defined with glass manifestation on the glass at two levels; between 850-1,000 mm and 1,400-1,600 mm above the floor, contrasting visually with the background seen through the glass (both inside and out) in all lighting conditions.
Manifestation takes the form of logo or sign at least 150 mm high (repeated if on a glazed screen), or a decorative feature such as broken lines or continuous bands, at least 50 mm high.
|}

[[File:Manifestation_specification.jpg|link=File:Manifestation_specification.jpg]]

The most simple manifestation is two rows of 50-75 mm white or frosted dots, however, the regulations do not dictate the appearance of the manifestation. Standard designs of dots, squares and simple bands are common, but large panels in etched or printed film with cut-out clear spaces, or [https://www.windowfilm.co.uk/graphics/glass-manifestation branded manifestation with logos] or other designs are also acceptable.

Alternative solutions such as mullions, transoms, door frames or large pull handles / push plates may also be acceptable.

In addition, doors should be apparent from the side, if they can be held open, and where glazed doors are beside a glazed screen, they should be marked with a high contrast strip along the top and at both sides.

=== [https://www.windowfilm.co.uk/graphics/manifestation-legislation Glass Manifestation Regulations & Legislation]<br />
<br />
The approved document to Part M of the Building Regulations - access to and use of buildings - states that people with visual impairment should be in no doubt as to the location of glass doors and screens, and steps should be taken to avoid people being harmed by walking into them. This requirement is satisfied if they comply with approved document K, section 7. ===

= Find out more =

=== Related articles on Designing Buildings Wiki ===

* BFRC window rating scheme.
* Curved glass.
* Doors.
* Glass.
* Glass block flooring.
* Glazing.
* Low-E glass.
* Patent glazing.
* Security glazing.
* Types of window.

[[Category:Health_and_safety_/_CDM]] [[Category:Products_/_components]]