Sound insulation testing - Revision history

Designing Buildings at 09:52, 27 December 2021

2021-12-27T09:52:06Z

← Older revision		Revision as of 09:52, 27 December 2021
Line 5:		Line 5:
	= What are the sound insulation targets that need to be achieved? =		= What are the sound insulation targets that need to be achieved? =

−	The specific acoustic performance requirements for new builds and conversions are set within ~~[http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf~~ Approved Document E ‘resistance to the passage of sound’], as shown in the table.	+	The specific acoustic performance requirements for new builds and conversions are set within Approved Document E ‘resistance to the passage of sound’, as shown in the table.

	Requirement E1 – on-site airborne sound insulation performance targets for separating (party) walls and floors.		Requirement E1 – on-site airborne sound insulation performance targets for separating (party) walls and floors.

Editor at 16:45, 24 December 2021

2021-12-24T16:45:41Z

← Older revision		Revision as of 16:45, 24 December 2021
Line 106:		Line 106:
	This [https://www.parkerjonesacoustics.com/insights/articles/sound-testing-explained article was written by ParkerJones Acoustics] in January 2020.		This [https://www.parkerjonesacoustics.com/insights/articles/sound-testing-explained article was written by ParkerJones Acoustics] in January 2020.

−	= Related articles on Designing Buildings ~~Wiki~~ =	+	= Related articles on Designing Buildings =

	* Acoustic consultant.		* Acoustic consultant.
Line 120:		Line 120:
	* Flanking sound.		* Flanking sound.
	* Impact sound.		* Impact sound.
		+	* Noise level.
	* Noise nuisance.		* Noise nuisance.
	* Pre-completion sound testing.		* Pre-completion sound testing.

Designing Buildings at 07:32, 31 January 2021

2021-01-31T07:32:54Z

← Older revision		Revision as of 07:32, 31 January 2021
Line 134:		Line 134:
	--[[User:ParkerJonesAcoustics\|ParkerJonesAcoustics]]		--[[User:ParkerJonesAcoustics\|ParkerJonesAcoustics]]

−	[[Category:~~Research_/_Innovation~~]] [[Category:DCN_Research,_Development_and_Innovation]] [[Category:~~Theory~~]] [[Category:~~Design~~]] [[Category:~~Products_/_components~~]] [[Category:~~DCN_Product_Knowledge~~]]	+	[[Category:DCN_Commentary]] [[Category:DCN_Guidance]] [[Category:DCN_Product_Knowledge]] [[Category:DCN_Research,_Development_and_Innovation]] [[Category:Research_/_Innovation]] [[Category:Theory]] [[Category:Design]] [[Category:Products_/_components]]

Designing Buildings at 06:56, 17 January 2020

2020-01-17T06:56:48Z

← Older revision		Revision as of 06:56, 17 January 2020
Line 56:		Line 56:

	{\|		{\|
−	\|width="100%"\| Sets of tests in flats with a separating floor and a separating wall	+	\|width="100%"\| Sets of tests in flats with a separating floor and a separating wall.
	\|-		\|-
	\| [[File:Sound_Test_sets_1_no_text.png\|link=File:Sound_Test_sets_1_no_text.png]]		\| [[File:Sound_Test_sets_1_no_text.png\|link=File:Sound_Test_sets_1_no_text.png]]
Line 63:		Line 63:
	One set of tests should compromise six tests (four airborne, two impact):		One set of tests should compromise six tests (four airborne, two impact):

−	• One airborne test across a wall between (where possible) a pair of living rooms.	+	* One airborne test across a wall between (where possible) a pair of living rooms.
−		+	* One airborne test across a wall between (where possible) a pair of bedrooms.
−	• One airborne test across a wall between (where possible) a pair of bedrooms.	+	* One airborne and one impact test across a floor between (where possible) a pair of living rooms
−		+	* One airborne and one impact test across a floor between (where possible) a pair of bedrooms
−	• One airborne and one impact test across a floor between (where possible) a pair of living rooms	+
−		+
−	• One airborne and one impact test across a floor between (where possible) a pair of bedrooms	+
	\|}		\|}

Line 75:		Line 72:
	\|width="50%"\| [[File:Sound_Test_sets_2_no_text.png\|link=File:Sound_Test_sets_2_no_text.png]]		\|width="50%"\| [[File:Sound_Test_sets_2_no_text.png\|link=File:Sound_Test_sets_2_no_text.png]]
	\|width="50%"\|		\|width="50%"\|
−	Sets of tests in flats with separating floors but without separating walls	+	Sets of tests in flats with separating floors but without separating walls.

	One set of tests should compromise four tests (two airborne, two impact):		One set of tests should compromise four tests (two airborne, two impact):

−	• One airborne and one impact test across a floor between (where possible) a pair of living rooms	+	* One airborne and one impact test across a floor between (where possible) a pair of living rooms
−		+	* One airborne and one impact test across a floor between (where possible) a pair of bedrooms
−	• One airborne and one impact test across a floor between (where possible) a pair of bedrooms	+
	\|}		\|}

	{\|		{\|
−	\|width="100%"\| Sets of tests in dwelling-houses with separating walls but no separating floors	+	\|width="100%"\| Sets of tests in dwelling-houses with separating walls but no separating floors.
	\|-		\|-
	\| [[File:Sound_Test_sets_3_no_text.png\|link=File:Sound_Test_sets_3_no_text.png]]		\| [[File:Sound_Test_sets_3_no_text.png\|link=File:Sound_Test_sets_3_no_text.png]]
Line 92:		Line 88:
	One set of tests should compromise two tests (two airborne):		One set of tests should compromise two tests (two airborne):

−	• One airborne test across a wall between (where possible) a pair of living rooms.	+	* One airborne test across a wall between (where possible) a pair of living rooms.
−		+	* One airborne test across a wall between (where possible) a pair of bedrooms.
−	• One airborne test across a wall between (where possible) a pair of bedrooms.	+
	\|}		\|}

−	=== What condition should the site be in for sound testing? ===	+	= What condition should the site be in for sound testing? =

−	Sound testing should ideally be conducted after completion of the building works, or as close to completion as possible. A failed acoustic test can often be down to constructions not being completed, penetrations and air gaps not being sealed, doors not being in place.	+	Sound testing should ideally be conducted after completion of the building works, or as close to completion as possible. A failed acoustic test can often be down to constructions not being completed, penetrations and air gaps not being sealed or doors not being in place.

−	An acoustic consultant will also ask for ~~a bit of~~ quiet. If asked to come to site a few weeks before completion and there are still a lot of construction works and snagging going on, the acoustic testing results may be adversely influenced by this noise.	+	An acoustic consultant will also ask for quiet. If asked to come to site a few weeks before completion and there are still a lot of construction works and snagging going on, the acoustic testing results may be adversely influenced by this noise.

	The acoustic consultant may welcome the provision of 240V power on site. While some acoustic engineers use battery-operated equipment, many do not, and having to carry a transformer with an extension lead can mean that testing takes longer, which may mean more site visits, and therefore more cost for the client.		The acoustic consultant may welcome the provision of 240V power on site. While some acoustic engineers use battery-operated equipment, many do not, and having to carry a transformer with an extension lead can mean that testing takes longer, which may mean more site visits, and therefore more cost for the client.
Line 109:		Line 104:
	= About this article =		= About this article =

−	This a[https://www.parkerjonesacoustics.com/insights/articles/sound-testing-explained ~~rticle~~ was written by ParkerJones Acoustics] in January 2020.	+	This [https://www.parkerjonesacoustics.com/insights/articles/sound-testing-explained article was written by ParkerJones Acoustics] in January 2020.

	= Related articles on Designing Buildings Wiki =		= Related articles on Designing Buildings Wiki =
Line 139:		Line 134:
	--[[User:ParkerJonesAcoustics\|ParkerJonesAcoustics]]		--[[User:ParkerJonesAcoustics\|ParkerJonesAcoustics]]

−	[[Category:Research_/_Innovation]] [[Category:Theory]] [[Category:Design]] [[Category:Products_/_components]]	+	[[Category:Research_/_Innovation]] [[Category:DCN_Research,_Development_and_Innovation]] [[Category:Theory]] [[Category:Design]] [[Category:Products_/_components]] [[Category:DCN_Product_Knowledge]]

Designing Buildings at 06:53, 17 January 2020

2020-01-17T06:53:02Z

Editor at 11:32, 14 January 2020

2020-01-14T11:32:44Z

Show changes

Editor at 11:02, 14 January 2020

2020-01-14T11:02:10Z

← Older revision		Revision as of 11:02, 14 January 2020
Line 9:		Line 9:
	Requirement E1 – on-site airborne sound insulation performance targets for separating (party) walls and floors		Requirement E1 – on-site airborne sound insulation performance targets for separating (party) walls and floors

−	[[File:~~Sound insulation targets for residential~~.jpg]]	+	[[File:Sound_insulation_targets_for_residential.jpg\|link=File:Sound_insulation_targets_for_residential.jpg]]

	[http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf Approved Document E] classes ‘rooms for residential purposes’ means a room, or a suite of rooms, which is not a dwelling-house or a flat and which is used by one or more persons to live and sleep and includes a room in a hostel, a hotel, a boarding house, a hall of residence or a residential home, but does not include a room in a hospital or other similar establishment used for patient accommodation.		[http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf Approved Document E] classes ‘rooms for residential purposes’ means a room, or a suite of rooms, which is not a dwelling-house or a flat and which is used by one or more persons to live and sleep and includes a room in a hostel, a hotel, a boarding house, a hall of residence or a residential home, but does not include a room in a hospital or other similar establishment used for patient accommodation.
Line 58:		Line 58:
	\|width="100%"\| Sets of tests in flats with a separating floor and a separating wall		\|width="100%"\| Sets of tests in flats with a separating floor and a separating wall
	\|-		\|-
−	\| [[File:~~Sound Test sets 1 no text~~.png]]	+	\| [[File:Sound_Test_sets_1_no_text.png\|link=File:Sound_Test_sets_1_no_text.png]]
	\|-		\|-
	\|		\|
Line 73:		Line 73:

	{\|		{\|
−	\|width="50%"\| [[File:~~Sound Test sets 2 no text~~.png]]	+	\|width="50%"\| [[File:Sound_Test_sets_2_no_text.png\|link=File:Sound_Test_sets_2_no_text.png]]
	\|width="50%"\|		\|width="50%"\|
	Sets of tests in flats with separating floors but without separating walls		Sets of tests in flats with separating floors but without separating walls
Line 87:		Line 87:
	\|width="100%"\| Sets of tests in dwelling-houses with separating walls but no separating floors		\|width="100%"\| Sets of tests in dwelling-houses with separating walls but no separating floors
	\|-		\|-
−	\| [[File:~~Sound Test sets 3 no text~~.png]]	+	\| [[File:Sound_Test_sets_3_no_text.png\|link=File:Sound_Test_sets_3_no_text.png]]
	\|-		\|-
	\|		\|
Line 107:		Line 107:
	Lastly, something that is often overlooked, is that impact sound insulation testing should be conducted in residential developments without the floor finish. A carpet floor finish is a very good dampener of impacts upon the floor. But in a few years, what if the occupant decides they would like to change this to hard flooring? Answer, the level of impact sound insulation could get much worse. Therefore to safeguard against this, impact sound insulation testing must be conducted without the floor finish (unless it can be argued that the finish is integral and cannot be changed later down the line). It’s for this reason that party floors usually have an acoustic/resilient underlay within the floor construction, or beneath the floor finish.		Lastly, something that is often overlooked, is that impact sound insulation testing should be conducted in residential developments without the floor finish. A carpet floor finish is a very good dampener of impacts upon the floor. But in a few years, what if the occupant decides they would like to change this to hard flooring? Answer, the level of impact sound insulation could get much worse. Therefore to safeguard against this, impact sound insulation testing must be conducted without the floor finish (unless it can be argued that the finish is integral and cannot be changed later down the line). It’s for this reason that party floors usually have an acoustic/resilient underlay within the floor construction, or beneath the floor finish.

−	[https://www.parkerjonesacoustics.com/insights/articles/sound-testing-explained ~~Article~~ was written ~~and originally produced~~ by ParkerJones Acoustics.]	+	= About this article =
		+
		+	This a[https://www.parkerjonesacoustics.com/insights/articles/sound-testing-explained rticle was written by ParkerJones Acoustics] in January 2020.
		+
		+	= Related articles on Designing Buildings Wiki =
		+
		+	* Acoustic consultant.
		+	* Acoustic design for health and wellbeing.
		+	* Airborne sound.
		+	* Approved Document E.
		+	* Ash deafening.
		+	* Audio frequency.
		+	* BREEAM Acoustic performance.
		+	* Building Bulletin 93: acoustic design of schools.
		+	* Building regulations.
		+	* Decibel.
		+	* Flanking sound.
		+	* Impact sound.
		+	* Noise nuisance.
		+	* Pre-completion sound testing.
		+	* Reverberation.
		+	* Robust details certification scheme.
		+	* Sound absorption.
		+	* Sound insulation.
		+	* Sound insulation in dwellings: Part 1: An introduction (GG 83-1).
		+	* Sound reduction index (SRI).
		+	* Sound v noise.
		+	* Structure-borne sound.
		+	* Suitably Qualified Acoustician.
		+
		+	--[[User:ParkerJonesAcoustics\|ParkerJonesAcoustics]]
		+
		+	[[Category:Research_/_Innovation]] [[Category:Theory]] [[Category:Design]] [[Category:Products_/_components]]

ParkerJonesAcoustics at 02:13, 13 January 2020

2020-01-13T02:13:45Z

← Older revision		Revision as of 02:13, 13 January 2020
Line 9:		Line 9:
	Requirement E1 – on-site airborne sound insulation performance targets for separating (party) walls and floors		Requirement E1 – on-site airborne sound insulation performance targets for separating (party) walls and floors

−	~~Separating Element~~	+	[[File:Sound insulation targets for residential.jpg]]
−		+
−	~~Airborne sound~~ insulation	+
−		+
−	~~DnT,w + Ctr dB~~	+
−		+
−	~~(minimum values)~~	+
−		+
−	~~Impact sound insulation~~	+
−		+
−	~~L’nT,w dB~~	+
−		+
−	~~(maximum values)~~	+
−		+
−	~~Purpose built dwelling-houses and flats (new build)~~	+
−		+
−	~~Walls~~	+
−		+
−	45	+
−		+
−	–	+
−		+
−	~~Floors and Stairs~~	+
−		+
−	45	+
−		+
−	62	+
−		+
−	~~Dwelling-houses and flats formed by material change of use (refurbishment)~~	+
−		+
−	~~Walls~~	+
−		+
−	43	+
−		+
−	–	+
−		+
−	~~Floors and Stairs~~	+
−		+
−	43	+
−		+
−	64	+
−		+
−	~~Purpose built rooms for residential purposes (new build)~~	+
−		+
−	~~Walls~~	+
−		+
−	43	+
−		+
−	–	+
−		+
−	~~Floors and Stairs~~	+
−		+
−	43	+
−		+
−	62	+
−		+
−	~~Rooms~~ for residential ~~purposes formed by material change of use (refurbishment)~~	+
−		+
−	~~Walls~~	+
−		+
−	43	+
−		+
−	–	+
−		+
−	~~Floors and Stairs~~	+
−		+
−	43	+
−		+
−	62	+

	[http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf Approved Document E] classes ‘rooms for residential purposes’ means a room, or a suite of rooms, which is not a dwelling-house or a flat and which is used by one or more persons to live and sleep and includes a room in a hostel, a hotel, a boarding house, a hall of residence or a residential home, but does not include a room in a hospital or other similar establishment used for patient accommodation.		[http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf Approved Document E] classes ‘rooms for residential purposes’ means a room, or a suite of rooms, which is not a dwelling-house or a flat and which is used by one or more persons to live and sleep and includes a room in a hostel, a hotel, a boarding house, a hall of residence or a residential home, but does not include a room in a hospital or other similar establishment used for patient accommodation.
Line 126:		Line 58:
	\|width="100%"\| Sets of tests in flats with a separating floor and a separating wall		\|width="100%"\| Sets of tests in flats with a separating floor and a separating wall
	\|-		\|-
−	\| [[File:Sound-Test-sets-1-no-text.~~jpg\|1821px~~]]	+	\| [[File:Sound Test sets 1 no text.png]]
	\|-		\|-
	\|		\|
Line 141:		Line 73:

	{\|		{\|
−	\|width="50%"\| [[File:Sound-Test-sets-2-no-text.~~jpg\|300px~~]]	+	\|width="50%"\| [[File:Sound Test sets 2 no text.png]]
	\|width="50%"\|		\|width="50%"\|
	Sets of tests in flats with separating floors but without separating walls		Sets of tests in flats with separating floors but without separating walls
		+
	One set of tests should compromise 4 tests (2 airborne, 2 impact):		One set of tests should compromise 4 tests (2 airborne, 2 impact):

Line 154:		Line 87:
	\|width="100%"\| Sets of tests in dwelling-houses with separating walls but no separating floors		\|width="100%"\| Sets of tests in dwelling-houses with separating walls but no separating floors
	\|-		\|-
−	\| [[File:Sound-Test-sets-3-no-text.~~jpg\|1821px~~]]	+	\| [[File:Sound Test sets 3 no text.png]]
	\|-		\|-
	\|		\|
Line 174:		Line 107:
	Lastly, something that is often overlooked, is that impact sound insulation testing should be conducted in residential developments without the floor finish. A carpet floor finish is a very good dampener of impacts upon the floor. But in a few years, what if the occupant decides they would like to change this to hard flooring? Answer, the level of impact sound insulation could get much worse. Therefore to safeguard against this, impact sound insulation testing must be conducted without the floor finish (unless it can be argued that the finish is integral and cannot be changed later down the line). It’s for this reason that party floors usually have an acoustic/resilient underlay within the floor construction, or beneath the floor finish.		Lastly, something that is often overlooked, is that impact sound insulation testing should be conducted in residential developments without the floor finish. A carpet floor finish is a very good dampener of impacts upon the floor. But in a few years, what if the occupant decides they would like to change this to hard flooring? Answer, the level of impact sound insulation could get much worse. Therefore to safeguard against this, impact sound insulation testing must be conducted without the floor finish (unless it can be argued that the finish is integral and cannot be changed later down the line). It’s for this reason that party floors usually have an acoustic/resilient underlay within the floor construction, or beneath the floor finish.

−	[https://www.parkerjonesacoustics.com/insights/articles/sound-testing-explained Article written and originally produced by ParkerJones Acoustics.]	+	[https://www.parkerjonesacoustics.com/insights/articles/sound-testing-explained Article was written and originally produced by ParkerJones Acoustics.]

ParkerJonesAcoustics: Created page with "== Sound Testing to comply with Part E for Residential Developments == There are many sets of Building Regulations requirements which a new or refurbished residential developmen..."

2020-01-13T02:07:09Z

Created page with "== Sound Testing to comply with Part E for Residential Developments == There are many sets of Building Regulations requirements which a new or refurbished residential developmen..."

New page

== Sound Testing to comply with Part E for Residential Developments ==

There are many sets of Building Regulations requirements which a new or refurbished residential development must meet. One of these, is to achieve a minimum standard of sound insulation performance internally between dwellings. This is an important regulation, as we seek some level of sound privacy from our neighbours, ensuring we can live and sleep in peace.

=== What are the Sound Insulation targets I need to achieve? ===

The specific acoustic performance requirements for new builds and conversions are set within [http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf Approved Document E ‘resistance to the passage of sound’], as shown in the table.

Requirement E1 – on-site airborne sound insulation performance targets for separating (party) walls and floors

Separating Element

Airborne sound insulation

DnT,w + Ctr dB

(minimum values)

Impact sound insulation

L’nT,w dB

(maximum values)

Purpose built dwelling-houses and flats (new build)

Walls

45

–

Floors and Stairs

45

62

Dwelling-houses and flats formed by material change of use (refurbishment)

Walls

43

–

Floors and Stairs

43

64

Purpose built rooms for residential purposes (new build)

Walls

43

–

Floors and Stairs

43

62

Rooms for residential purposes formed by material change of use (refurbishment)

Walls

43

–

Floors and Stairs

43

62

[http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf Approved Document E] classes ‘rooms for residential purposes’ means a room, or a suite of rooms, which is not a dwelling-house or a flat and which is used by one or more persons to live and sleep and includes a room in a hostel, a hotel, a boarding house, a hall of residence or a residential home, but does not include a room in a hospital or other similar establishment used for patient accommodation.

As shown above, the criteria for refurbishments are slightly more lenient than for new builds. This recognises that it can be more difficult to soundproof an existing structure if it cannot replaced, compared to implementing a construction from scratch.

This relates to sound insulation internally, between residential properties which share a separating wall or floor. It relates to separate properties, not internal walls/floors within a dwelling, which carry a much lower requirement for sound insulation which is not subject to sound testings.

Standards for noise ingress from outside (i.e. road traffic) are not covered under ADE and the Building Regulations, with the local planning authority having more of an input into what they consider to be a suitable internal noise level target.

=== What is Airborne Sound Insulation and a DnT,w + Ctr? ===

Airborne sound insulation relates to sound that travels via the air and through separating structures between rooms. For example, airborne sound across a lightweight floor would pass through the plasterboard ceiling, into the floor void, through the floorboards and into the room. It relates to noise sources such as speech, music, television sound…any noise source that radiates into the air, rather than directly into the structure.

The DnT,w + Ctr relates to a level of on-site sound insulation. In simple terms, put a noise source in one room (the ‘source room’), measure the noise level, then go next door (the ‘receiver room’) and measure again, then calculate the difference. Well actually, this would be a ‘D’. A Dw is similar, but with the ‘w’ denoting a weighting across frequency which accounts for the way humans perceive different frequencies. A DnT,w is a Dw which is then ‘normalised’ to account for the reverberation time of the room (the ‘nT’), recognising that the level difference is dependant on how reverberant the receiver room is, and that every room will have a slightly different reverberation time, hence we need to normalise the result to assess every sound test on a level playing field against a fixed target. A DnT,w + Ctr then adds the addition of a low frequency correction (the ‘Ctr’), as low frequency noise is difficult to control and therefore the regulations add this correction to improve the standard of sound insulation against low frequency noise such as music.

Confused? Lets look at it really roughly. Take a source level in one flat of 100 dB(A), then a receiver level in the neighbouring flat of 55 dB(A), the level difference is 45 dB, hence our sound insulation performance should be somewhere in the region of 45 dB DnT,w + Ctr…

The higher the DnT,w + Ctr, the better the level of airborne sound insulation.

=== What is Impact Sound Insulation and an L’nT,w? ===

Impact sound insulation relates to noise generated by actual impact on a structure. Hence this typically is only assessed for intermediate floors, to consider noise such as footsteps, chair scrapes and any other object being dropped or impacting on the floor.

The L’nT,w is determined from measuring sound levels within a room where the floor above is being excited by an impact. Your acoustic consultant will use what’s called a ‘tapping machine’ to do this, which drops a series of weights/hammers on the floor in regular succession at a fixed force (as if the acoustic engineer varied the force every time they test, they’d get completely different results!).

The lower the L’nT,w, the better the level of impact sound insulation.

=== What does Sound Testing actually involve? ===

For compliance with the Building Regulations, the acoustic testing must be conducted by a qualified acoustic engineer who is accredited to conduct sound testing by an organisation such as [https://www.ukas.com/news/technical-bulletin-sound-insulation-testing-and-reuse-of-reverberation-time-measurements/ Ukas] or the [https://www.association-of-noise-consultants.co.uk/services/sound-insulation-testing/ Association of Noise Consultants]. Such an engineer will be using expensive equipment including a Class 1 sound level meter which costs several thousand pounds… so don’t try this with your noise meter bought for a few quid!

Airborne sound insulation tests are conducted by placing a loudspeaker, or two loudspeakers in the ‘source’ room. These loudspeakers are use to play white or pink noise at a very high amplitude, to the tune of 95 – 110 dB(A) within the room (the acoustic engineer will be wearing hearing protection!). The reason for using this type of noise, is that it is constant in amplitude, with an even spread of sound energy across frequency, keeping our test nice and consistent. The engineer will use their sound level meter to make a series of measurements in the source room. They will then go to the adjacent room (with the loudspeaker still on) and take a series of measurements within the ‘receiver’ room.

After turning off the loudspeaker, two other tests will be made in the receiver room. One is to measure the reverberation time (to get the ‘nT’ correction in DnT,w + Ctr), which can be achieved by generating an impulse in the room, using the sound level meter to measure/calculate the time taken for sound to decay by 60 dB. The impulse can be made by popping a balloon, shooting a starter pistol, or using the loudspeaker to generate white noise and then abruptly turning it off. The reverberation time affects how much sound energy bounces around the room, therefore affecting sound levels in the receiver room, which therefore affects the level difference from the sound source next door. The second test, is to measure background noise. If we’re measuring a high level of sound insulation then we might expect that background noise from other noise sources will be at a similar level to the level in the receiver room from our noise source next door, therefore we have to make a correction for this.

Putting these all together, the measurements of level difference, reverberation time, and background noise, enables us to calculate the result DnT,w + Ctr.

Impact sound insulation tests as alluded to earlier, are conducted using a ‘tapping’ machine. This machine is placed upon the floor and set to work, where the acoustic consultant will then move downstairs to measure in the room below. As per airborne sound tests, the acoustic engineer will measure reverberation time and background noise in the receiver room. Putting all this together enables the consultant to calculate the L’nT,w.

=== How many Sound Tests do I need? ===

In large scale residential developments, we’re going to have a certain level of repeatability. Do we need to test every single wall and floor? No. Lets say for example, we have a building containing 10 very similar flats, with the same constructions and construction detailing between them. For this, ADE indicates that we would only need 1 ‘set’ of tests, as it suggests that at least ‘one set of tests for every ten dwelling-houses, flats or rooms for residential purposes in a group or sub-group’.

So what defines a ‘set’ of tests?

{|
|width="100%"| Sets of tests in flats with a separating floor and a separating wall
|-
| [[File:Sound-Test-sets-1-no-text.jpg|1821px]]
|-
|
One set of tests should compromise 6 tests (4 airborne, 2 impact):

• 1 airborne test across a wall between (where possible) a pair of living rooms

• 1 airborne test across a wall between (where possible) a pair of bedrooms

• 1 airborne and 1 impact test across a floor between (where possible) a pair of living rooms

• 1 airborne and 1 impact test across a floor between (where possible) a pair of bedrooms
|}

{|
|width="50%"| [[File:Sound-Test-sets-2-no-text.jpg|300px]]
|width="50%"|
Sets of tests in flats with separating floors but without separating walls
One set of tests should compromise 4 tests (2 airborne, 2 impact):

• 1 airborne and 1 impact test across a floor between (where possible) a pair of living rooms

• 1 airborne and 1 impact test across a floor between (where possible) a pair of bedrooms
|}

{|
|width="100%"| Sets of tests in dwelling-houses with separating walls but no separating floors
|-
| [[File:Sound-Test-sets-3-no-text.jpg|1821px]]
|-
|
One set of tests should compromise 2 tests (2 airborne):

• 1 airborne test across a wall between (where possible) a pair of living rooms

• 1 airborne test across a wall between (where possible) a pair of bedrooms
|}

=== What condition should my site be in for Sound Testing? ===

Sound testing should ideally be conducted after completion of the building works, or as close to completion as possible. A failed acoustic test can often be down to constructions not being completed, penetrations and air gaps not being sealed, doors not being in place…

Your acoustic consultant will also ask for a bit of quiet. If you ask your acoustic engineer to come to site a few weeks before completion and there are still a lot of construction works and snagging going on, then the acoustic testing results may be adversely influenced by this noise.

Your acoustic consultant may thank you if you can provide 240v power on site. Whilst some acoustic engineers use battery-operated equipment, many don’t, and having to carry a transformer with an extension lead can mean that testing takes longer, which may mean more site visits, and therefore more cost for you.

Lastly, something that is often overlooked, is that impact sound insulation testing should be conducted in residential developments without the floor finish. A carpet floor finish is a very good dampener of impacts upon the floor. But in a few years, what if the occupant decides they would like to change this to hard flooring? Answer, the level of impact sound insulation could get much worse. Therefore to safeguard against this, impact sound insulation testing must be conducted without the floor finish (unless it can be argued that the finish is integral and cannot be changed later down the line). It’s for this reason that party floors usually have an acoustic/resilient underlay within the floor construction, or beneath the floor finish.

[https://www.parkerjonesacoustics.com/insights/articles/sound-testing-explained Article written and originally produced by ParkerJones Acoustics.]

← Older revision		Revision as of 06:53, 17 January 2020
Line 3:		Line 3:
	There are many sets of Building Regulations requirements which a new or refurbished residential development must meet. One of these is to achieve a minimum standard of sound insulation performance internally between dwellings. This is an important regulation, as neighbours seek some level of sound privacy from their neighbours, ensuring all can live and sleep in peace.		There are many sets of Building Regulations requirements which a new or refurbished residential development must meet. One of these is to achieve a minimum standard of sound insulation performance internally between dwellings. This is an important regulation, as neighbours seek some level of sound privacy from their neighbours, ensuring all can live and sleep in peace.

−	=== What are the sound insulation targets that need to be achieved? ===	+	= What are the sound insulation targets that need to be achieved? =

	The specific acoustic performance requirements for new builds and conversions are set within [http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf Approved Document E ‘resistance to the passage of sound’], as shown in the table.		The specific acoustic performance requirements for new builds and conversions are set within [http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf Approved Document E ‘resistance to the passage of sound’], as shown in the table.

−	Requirement E1 – on-site airborne sound insulation performance targets for separating (party) walls and floors	+	Requirement E1 – on-site airborne sound insulation performance targets for separating (party) walls and floors.

	[[File:Sound_insulation_targets_for_residential.jpg\|link=File:Sound_insulation_targets_for_residential.jpg]]		[[File:Sound_insulation_targets_for_residential.jpg\|link=File:Sound_insulation_targets_for_residential.jpg]]

−	~~[http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf~~ Approved Document E] classes ‘rooms for residential purposes’ as room, or a suite of rooms, which is not a dwelling-house or a flat and which is used by one or more persons to live and sleep and includes a room in a hostel, a hotel, a boarding house, a hall of residence or a residential home, but does not include a room in a hospital or other similar establishment used for patient accommodation.	+	Approved Document E classes ‘rooms for residential purposes’ as a room, or a suite of rooms, which is not a dwelling-house or a flat and which is used by one or more persons to live and sleep and includes a room in a hostel, a hotel, a boarding house, a hall of residence or a residential home, but does not include a room in a hospital or other similar establishment used for patient accommodation.

−	~~As shown above, the~~ criteria for refurbishments are slightly more lenient than for new builds. This recognises that it can be more difficult to soundproof an existing structure if it cannot replaced, compared to implementing a construction from scratch.	+	The criteria for refurbishments are slightly more lenient than for new builds. This recognises that it can be more difficult to soundproof an existing structure if it cannot be replaced, compared to implementing a construction from scratch.

−	This relates to sound insulation internally, between residential properties which share a separating wall or floor. It relates to separate properties, not internal walls/floors within a dwelling, which carry a much lower requirement for sound insulation and which is not subject to sound testings.	+	This relates to sound insulation internally, between residential properties which share a separating wall or floor. It relates to separate properties, not internal walls/floors within a dwelling, which carry a much lower requirement for sound insulation and which are not subject to sound testings.

−	Standards for noise ingress from outside (i.e. road traffic) are not covered under ~~[http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf~~ Approved Document E~~] and the Building Regulations~~, with the local planning authority having more of an input into what it considers to be a suitable internal noise-level target.	+	Standards for noise ingress from outside (i.e. road traffic) are not covered under Approved Document E, with the local planning authority having more of an input into what it considers to be a suitable internal noise-level target.

−	=== What is airborne sound insulation and a DnT,w + Ctr? ===	+	= What is airborne sound insulation and a DnT,w + Ctr? =

−	Airborne sound insulation relates to sound that travels via the air ~~and~~ through separating structures between rooms. For example, airborne sound across a lightweight floor would pass through the plasterboard ceiling, into the floor void, through the floorboards and into the room. It relates to noise sources such as speech, music, television ~~sound…any~~ noise source that radiates into the air, rather than directly into the structure.	+	Airborne sound insulation relates to sound that travels via the air through separating structures between rooms. For example, airborne sound across a lightweight floor would pass through the plasterboard ceiling, into the floor void, through the floorboards and into the room. It relates to noise sources such as speech, music, television sound, and any noise source that radiates into the air, rather than directly into the structure.

−	The DnT,w + Ctr relates to a level of on-site sound insulation. In simple terms, put a noise source in one room (the ‘source room’), measure the noise level, then go next door (the ‘receiver room’) and measure again, then calculate the difference. ~~Well actually, this~~ would be a ‘D’. A Dw is similar, but with the ‘w’ denoting a weighting across frequency which accounts for the way humans perceive different frequencies. A DnT,w is a Dw which is then ‘normalised’ to account for the reverberation time of the room (the ‘nT’), recognising that the level difference is dependant on how reverberant the receiver room is, and that every room will have a slightly different reverberation time, hence we need to normalise the result to assess every sound test on a level playing field against a fixed target. A DnT,w + Ctr then adds the addition of a low-frequency correction (the ‘Ctr’), as low-frequency noise is difficult to control and therefore the regulations add this correction to improve the standard of sound insulation against low-frequency noise such as music.	+	The DnT,w + Ctr relates to a level of on-site sound insulation. In simple terms, put a noise source in one room (the ‘source room’), measure the noise level, then go next door (the ‘receiver room’) and measure again, then calculate the difference. This would be a ‘D’. A Dw is similar, but with the ‘w’ denoting a weighting across frequency which accounts for the way humans perceive different frequencies. A DnT,w is a Dw which is then ‘normalised’ to account for the reverberation time of the room (the ‘nT’), recognising that the level difference is dependant on how reverberant the receiver room is, and that every room will have a slightly different reverberation time, hence we need to normalise the result to assess every sound test on a level playing field against a fixed target. A DnT,w + Ctr then adds the addition of a low-frequency correction (the ‘Ctr’), as low-frequency noise is difficult to control and therefore the regulations add this correction to improve the standard of sound insulation against low-frequency noise such as music.

−	~~Confused?~~ Here is an outline expanation. Take a source level in one flat of 100 dB(A), then a receiver level in the neighbouring flat of 55 dB(A), the level difference is 45 dB, hence our sound insulation performance should be somewhere in the region of 45 dB DnT,w + ~~Ctr…~~	+	Here is an outline expanation. Take a source level in one flat of 100 dB(A), then a receiver level in the neighbouring flat of 55 dB(A), the level difference is 45 dB, hence our sound insulation performance should be somewhere in the region of 45 dB DnT,w + Ctr.

	The higher the DnT,w + Ctr, the better the level of airborne sound insulation.		The higher the DnT,w + Ctr, the better the level of airborne sound insulation.

−	=== What is impact sound insulation and an L’nT,w? ===	+	= What is impact sound insulation and an L’nT,w? =

−	Impact sound insulation relates to noise generated by actual impact on a structure. ~~Hence this typically~~ is only assessed for intermediate floors, to consider noise such as footsteps, chair scrapes and any other object being dropped or impacting on the floor.	+	Impact sound insulation relates to noise generated by actual impact on a structure. This is typically only assessed for intermediate floors, to consider noise such as footsteps, chair scrapes and any other object being dropped or impacting on the floor.

−	The L’nT,w is determined ~~from~~ measuring sound levels within a room where the floor above is being excited by an impact. ~~Your~~ acoustic consultant will use what is called a ‘tapping machine’ to do this, which drops a series of weights/hammers on the floor in regular succession at a fixed force (~~for~~ if ~~the acoustic engineer~~ varied the force every time they tested, they would get completely different results).	+	The L’nT,w is determined by measuring sound levels within a room where the floor above is being excited by an impact. An acoustic consultant will use what is called a ‘tapping machine’ to do this, which drops a series of weights/hammers on the floor in regular succession at a fixed force (if they varied the force every time they tested, they would get completely different results).

	The lower the L’nT,w, the better the level of impact sound insulation.		The lower the L’nT,w, the better the level of impact sound insulation.

−	=== What does sound testing actually involve? ===	+	= What does sound testing actually involve? =

−	For compliance with the Building Regulations, the acoustic testing must be conducted by a qualified acoustic engineer who is accredited to conduct sound testing by an organisation such as ~~[https://www.ukas.com/news/technical-bulletin-sound-insulation-testing-and-reuse-of-reverberation-time-measurements/~~ Ukas] or the ~~[https://www.association-of-noise-consultants.co.uk/services/sound-insulation-testing/~~ Association of Noise Consultants]. Such an engineer will be using expensive equipment, including a Class 1 sound-level meter which costs several thousand pounds… so do not try this with a noise meter bought for a few pounds.	+	For compliance with the Building Regulations, the acoustic testing must be conducted by a qualified acoustic engineer who is accredited to conduct sound testing by an organisation such as Ukas or the Association of Noise Consultants. Such an engineer will be using expensive equipment, including a Class 1 sound-level meter which costs several thousand pounds… so do not try this with a noise meter bought for a few pounds.

	Airborne sound insulation tests are conducted by placing a loudspeaker, or two loudspeakers in the ‘source’ room. These loudspeakers are used to play white or pink noise at a very high amplitude, to the tune of 95 – 110 dB(A) within the room (the acoustic engineer will be wearing hearing protection). The reason for using this type of noise, is that it is constant in amplitude, with an even spread of sound energy across frequency, keeping the test consistent. The engineer will use their sound-level meter to make a series of measurements in the source room. They will then go to the adjacent room (with the loudspeaker still on) and take a series of measurements within the ‘receiver’ room.		Airborne sound insulation tests are conducted by placing a loudspeaker, or two loudspeakers in the ‘source’ room. These loudspeakers are used to play white or pink noise at a very high amplitude, to the tune of 95 – 110 dB(A) within the room (the acoustic engineer will be wearing hearing protection). The reason for using this type of noise, is that it is constant in amplitude, with an even spread of sound energy across frequency, keeping the test consistent. The engineer will use their sound-level meter to make a series of measurements in the source room. They will then go to the adjacent room (with the loudspeaker still on) and take a series of measurements within the ‘receiver’ room.

−	After turning off the loudspeaker, two other tests will be made in the receiver room. One is to measure the reverberation time (to get the ‘nT’ correction in DnT,w + Ctr), which can be achieved by generating an impulse in the room, using the sound-level meter to measure/calculate the time taken for sound to decay by 60 dB. The impulse can be made by popping a balloon, shooting a starter pistol, or using the loudspeaker to generate white noise and then abruptly turning it off. The reverberation time affects how much sound energy bounces around the room, therefore affecting sound levels in the receiver room, which ~~therefore~~ affects the level difference from the sound source next door. The second test, is to measure background noise. If measuring a high level of sound insulation, it might be expected that background noise from other noise sources will be at a similar level to the level in the receiver room from the noise source next door, therefore a correction for this must be made.	+	After turning off the loudspeaker, two other tests will be made in the receiver room. One is to measure the reverberation time (to get the ‘nT’ correction in DnT,w + Ctr), which can be achieved by generating an impulse in the room, using the sound-level meter to measure/calculate the time taken for sound to decay by 60 dB. The impulse can be made by popping a balloon, shooting a starter pistol, or using the loudspeaker to generate white noise and then abruptly turning it off. The reverberation time affects how much sound energy bounces around the room, therefore affecting sound levels in the receiver room, which affects the level difference from the sound source next door. The second test, is to measure background noise. If measuring a high level of sound insulation, it might be expected that background noise from other noise sources will be at a similar level to the level in the receiver room from the noise source next door, therefore a correction for this must be made.

−	Putting these ~~all~~ together, the measurements of level difference, reverberation time, and background noise, enables the calculation of the result DnT,w + Ctr.	+	Putting these together, the measurements of level difference, reverberation time, and background noise, enables the calculation of the result DnT,w + Ctr.

−	Impact sound insulation tests as alluded to earlier, are conducted using a ‘tapping’ machine. This machine is placed ~~upon~~ the floor and set to work~~, when the~~ acoustic consultant will then move downstairs to measure in the room below. As per airborne sound tests, the acoustic engineer will measure reverberation time and background noise in the receiver room. Putting ~~all~~ this together enables the consultant to calculate the L’nT,w.	+	Impact sound insulation tests as alluded to earlier, are conducted using a ‘tapping’ machine. This machine is placed on the floor and set to work. The acoustic consultant will then move downstairs to measure in the room below. As per airborne sound tests, the acoustic engineer will measure reverberation time and background noise in the receiver room. Putting this together enables the consultant to calculate the L’nT,w.

−	=== How many sound tests are needed? ===	+	= How many sound tests are needed? =

−	In large-scale residential developments, there will be a certain level of repeatability. Does every single wall and floor need to be tested? No. Assume, for example, that we have a building containing 10 very similar flats, with the same constructions and construction detailing between them. For this, ~~[http://www.planningportal.gov.uk/uploads/br/BR_PDF_ADE_2003.pdf~~ Approved Document E] indicates that we would only need 1 ‘set’ of tests, as it suggests that at least ‘one set of tests for every ten dwelling-houses, flats or rooms for residential purposes in a group or sub-group’.	+	In large-scale residential developments, there will be a certain level of repeatability. Does every single wall and floor need to be tested? No. Assume, for example, that we have a building containing 10 very similar flats, with the same constructions and construction detailing between them. For this, Approved Document E indicates that we would only need 1 ‘set’ of tests, as it suggests that at least ‘one set of tests for every ten dwelling-houses, flats or rooms for residential purposes in a group or sub-group’.

−	=== So, what defines a ‘set’ of tests? ===	+	= So, what defines a ‘set’ of tests? =

	{\|		{\|