Outdoor porcelain tiles - Revision history

Designing Buildings at 06:02, 14 June 2021

2021-06-14T06:02:23Z

← Older revision		Revision as of 06:02, 14 June 2021
Line 5:		Line 5:
	= Frost resistance =		= Frost resistance =

−	The main indicator of exterior porcelain tiles is the frost resistance of the material. This characteristic is determined through a series of tests. The essence of the test consists ~~in the process~~ of ~~alternating~~ freezing-thawing of the sample and studying the consequences of this ~~effect~~.	+	The main indicator of exterior porcelain tiles is the frost resistance of the material. This characteristic is determined through a series of tests. The essence of the test consists of alternate freezing-thawing of the sample and studying the consequences of this.

−	The national certification procedure foresees 50 freeze-thaw cycles, but in practice, porcelain tiles should be able to withstand more than 200 cycles. ~~Therefore, it should suitable for safe placement on the street.~~	+	The national certification procedure foresees 50 freeze-thaw cycles, but in practice, porcelain tiles should be able to withstand more than 200 cycles. The material itself should work in a temperature range from frost down to -50°C.
−		+
−	The material itself should work in a temperature range from frost down to -50°C.	+

	In addition, there is are special frost-resistant outdoor porcelain tiles which are suitable for laying in regions with a severe climate.		In addition, there is are special frost-resistant outdoor porcelain tiles which are suitable for laying in regions with a severe climate.
Line 15:		Line 13:
	= Water absorption =		= Water absorption =

−	The high frost resistance of outdoor porcelain tiles is due to its low moisture absorption. The water absorption of this ~~finishing~~ material does not exceed 0.05%, which is a very low ~~rate~~.	+	The high frost resistance of outdoor porcelain tiles is due to its low moisture absorption. The water absorption of this material does not exceed 0.05%, which is very low.

−	The destruction of the material occurs after the penetration of moisture into its pores, which begins to freeze, increases in volume and destroys the structure~~. Therefore, it is the low moisture absorption that provides the coating with high frost resistance~~.	+	The destruction of the material occurs after the penetration of moisture into its pores, which begins to freeze, increases in volume and destroys the structure.

	= Wear resistance =		= Wear resistance =

−	~~The main criterion of porcelain tiles used on the street is resistance to abrasion.~~ The wear resistance of outdoor porcelain tiles is determined by three criteria: hardness, resistance to deep wear and resistance to wear.	+	The wear resistance of outdoor porcelain tiles is determined by three criteria: hardness, resistance to deep wear and resistance to wear.

	For outdoor use, it is sufficient to use class 7 porcelain tiles according to the Mohs hardness scale. The Mohs scale designates the hardness class of a material from one to 10 (where one is talc and 10 is diamond).		For outdoor use, it is sufficient to use class 7 porcelain tiles according to the Mohs hardness scale. The Mohs scale designates the hardness class of a material from one to 10 (where one is talc and 10 is diamond).

−	According to EN 154 (European standard), ~~the~~ tests are carried out with a corundum roller. Depending on the speed of this roller on the surface of the porcelain tiles, which has not caused visible damage, the material is assigned a certain abrasion resistance class (PEI I - PEI V).	+	According to EN 154 (European standard), abrasian tests are carried out with a corundum roller. Depending on the speed of this roller on the surface of the porcelain tiles, which has not caused visible damage, the material is assigned a certain abrasion resistance class (PEI I - PEI V).

−	The deep wear resistance index is determined by the volume of material removed from the tile during ~~a special test~~. For outdoor porcelain tiles, this figure is in the range of 110-140 mm. According to EN 102, the limit for floor coverings must not exceed 250 mm.	+	The deep wear resistance index is determined by the volume of material removed from the tile during testing. For outdoor porcelain tiles, this figure is in the range of 110-140 mm. According to EN 102, the limit for floor coverings must not exceed 250 mm.

	= Related articles on Designing Buildings Wiki =		= Related articles on Designing Buildings Wiki =

Editor: Reverted edits by Priyasharma (talk) to last revision by Editor

2021-06-08T08:52:04Z

Reverted edits by Priyasharma (talk) to last revision by Editor

← Older revision		Revision as of 08:52, 8 June 2021
Line 7:		Line 7:
	The main indicator of exterior porcelain tiles is the frost resistance of the material. This characteristic is determined through a series of tests. The essence of the test consists in the process of alternating freezing-thawing of the sample and studying the consequences of this effect.		The main indicator of exterior porcelain tiles is the frost resistance of the material. This characteristic is determined through a series of tests. The essence of the test consists in the process of alternating freezing-thawing of the sample and studying the consequences of this effect.

−	The national certification procedure foresees 50 freeze-thaw cycles, but in practice, ~~[https://groupofmetro.com/~~porcelain-tiles ~~porcelain tiles]~~ should be able to withstand more than 200 cycles. Therefore, it should suitable for safe placement on the street.	+	The national certification procedure foresees 50 freeze-thaw cycles, but in practice, porcelain tiles should be able to withstand more than 200 cycles. Therefore, it should suitable for safe placement on the street.

	The material itself should work in a temperature range from frost down to -50°C.		The material itself should work in a temperature range from frost down to -50°C.

−	In addition, there is are special frost-resistant ~~[https://skytouchceramic.com/gvt-pgvt-outdoor-parking-tiles~~ outdoor porcelain tiles] which are suitable for laying in regions with a severe climate.	+	In addition, there is are special frost-resistant outdoor porcelain tiles which are suitable for laying in regions with a severe climate.

	= Water absorption =		= Water absorption =

Priyasharma at 08:43, 8 June 2021

2021-06-08T08:43:44Z

← Older revision		Revision as of 08:43, 8 June 2021
Line 7:		Line 7:
	The main indicator of exterior porcelain tiles is the frost resistance of the material. This characteristic is determined through a series of tests. The essence of the test consists in the process of alternating freezing-thawing of the sample and studying the consequences of this effect.		The main indicator of exterior porcelain tiles is the frost resistance of the material. This characteristic is determined through a series of tests. The essence of the test consists in the process of alternating freezing-thawing of the sample and studying the consequences of this effect.

−	The national certification procedure foresees 50 freeze-thaw cycles, but in practice, porcelain tiles should be able to withstand more than 200 cycles. Therefore, it should suitable for safe placement on the street.	+	The national certification procedure foresees 50 freeze-thaw cycles, but in practice, [https://groupofmetro.com/porcelain-tiles porcelain tiles] should be able to withstand more than 200 cycles. Therefore, it should suitable for safe placement on the street.

	The material itself should work in a temperature range from frost down to -50°C.		The material itself should work in a temperature range from frost down to -50°C.

−	In addition, there is are special frost-resistant outdoor porcelain tiles which are suitable for laying in regions with a severe climate.	+	In addition, there is are special frost-resistant [https://skytouchceramic.com/gvt-pgvt-outdoor-parking-tiles outdoor porcelain tiles] which are suitable for laying in regions with a severe climate.

	= Water absorption =		= Water absorption =

Editor at 08:10, 26 May 2021

2021-05-26T08:10:10Z

← Older revision		Revision as of 08:10, 26 May 2021
Line 23:		Line 23:
	The main criterion of porcelain tiles used on the street is resistance to abrasion. The wear resistance of outdoor porcelain tiles is determined by three criteria: hardness, resistance to deep wear and resistance to wear.		The main criterion of porcelain tiles used on the street is resistance to abrasion. The wear resistance of outdoor porcelain tiles is determined by three criteria: hardness, resistance to deep wear and resistance to wear.

−	For outdoor use, it is sufficient to use class 7 porcelain tiles according to ~~MOHS~~. The ~~MOHS~~ scale designates the hardness class of a material from one to 10 (where one is talc and 10 is diamond).	+	For outdoor use, it is sufficient to use class 7 porcelain tiles according to the Mohs hardness scale. The Mohs scale designates the hardness class of a material from one to 10 (where one is talc and 10 is diamond).

	According to EN 154 (European standard), the tests are carried out with a corundum roller. Depending on the speed of this roller on the surface of the porcelain tiles, which has not caused visible damage, the material is assigned a certain abrasion resistance class (PEI I - PEI V).		According to EN 154 (European standard), the tests are carried out with a corundum roller. Depending on the speed of this roller on the surface of the porcelain tiles, which has not caused visible damage, the material is assigned a certain abrasion resistance class (PEI I - PEI V).

Editor at 17:01, 25 May 2021

2021-05-25T17:01:25Z

← Older revision		Revision as of 17:01, 25 May 2021
Line 32:		Line 32:

	* Hardness.		* Hardness.
		+	* Mohs scale of mineral hardness.
	* Porcelain.		* Porcelain.
	* Porcelain tiles.		* Porcelain tiles.

Editor at 16:52, 24 May 2021

2021-05-24T16:52:06Z

← Older revision		Revision as of 16:52, 24 May 2021
Line 29:		Line 29:
	The deep wear resistance index is determined by the volume of material removed from the tile during a special test. For outdoor porcelain tiles, this figure is in the range of 110-140 mm. According to EN 102, the limit for floor coverings must not exceed 250 mm.		The deep wear resistance index is determined by the volume of material removed from the tile during a special test. For outdoor porcelain tiles, this figure is in the range of 110-140 mm. According to EN 102, the limit for floor coverings must not exceed 250 mm.

−	Related articles on Designing Buildings Wiki	+	= Related articles on Designing Buildings Wiki =
		+
		+	* Hardness.
		+	* Porcelain.
		+	* Porcelain tiles.
		+	* Types of flooring.

	[[Category:DCN_Product_Knowledge]] [[Category:Education]] [[Category:Products_/_components]]		[[Category:DCN_Product_Knowledge]] [[Category:Education]] [[Category:Products_/_components]]

Editor at 16:49, 24 May 2021

2021-05-24T16:49:06Z

← Older revision		Revision as of 16:49, 24 May 2021
Line 1:		Line 1:
−	=~~= Best Outdoor Porcelain Tiles =~~=	+	= Introduction =

−	Among the large selection of floor coverings, porcelain tiles deserves special attention. Its aesthetic properties and technical characteristics allow the material to be used everywhere. Today it can be placed in any room, regardless of its purpose, size, etc. There are several types of porcelain tiles~~, among which you can find the optimal model~~ for ~~any operating condition~~. ~~Particular attention should be paid to [https://skytouchceramic.com/gvt-pgvt-outdoor-parking-tiles outdoor porcelain tiles], which has all the necessary~~ properties ~~to ensure~~ the durability of the coating~~, even when used in an open space~~.	+	There are several types of porcelain tiles that are suitable for outdoor applications. Some of these products have properties that protect the durability of the coating under these conditions.

−	=~~= Properties Of Outdoor Porcelain Tiles =~~=	+	= Frost resistance =

−	~~=== Frost Resistance ===~~	+	The main indicator of exterior porcelain tiles is the frost resistance of the material. This characteristic is determined through a series of tests. The essence of the test consists in the process of alternating freezing-thawing of the sample and studying the consequences of this effect.

−	~~<br />~~	+	The national certification procedure foresees 50 freeze-thaw cycles, but in practice, porcelain tiles should be able to withstand more than 200 cycles. Therefore, it should suitable for safe placement on the street.
−	The main indicator of exterior [https://cruso.in/polished-glazed-porcelain-tiles porcelain tiles] is the frost resistance of the material. This characteristic is determined through a series of tests. The essence of the test consists in the process of alternating freezing-thawing of the sample and studying the consequences of this effect. The national certification procedure foresees 50 freeze-thaw cycles, but in practice, porcelain tiles ~~can~~ withstand more than 200 cycles. Therefore, it ~~can be safely placed~~ on the street.	+

−	The material itself ~~works perfectly~~ in ~~any~~ temperature range ~~(including~~ frost down to -~~50 ° C)~~.	+	The material itself should work in a temperature range from frost down to -50°C.

−	In addition, there is a special frost-resistant outdoor porcelain tiles, which ~~is ideal~~ for laying in regions with a severe ~~European~~ climate.	+	In addition, there is are special frost-resistant outdoor porcelain tiles which are suitable for laying in regions with a severe climate.

−	=== Water ~~Absorption ==~~=	+	= Water absorption =

−	~~<br />~~	+	The high frost resistance of outdoor porcelain tiles is due to its low moisture absorption. The water absorption of this finishing material does not exceed 0.05%, which is a very low rate.
−	The high frost resistance of outdoor porcelain tiles is due to its low moisture absorption. The water absorption of this finishing material does not exceed 0.05% ~~(very low). The destruction of the material occurs after the penetration of moisture into its pores~~, which ~~begins to freeze, increases in volume and destroys the structure. Therefore, it~~ is ~~the~~ low ~~moisture absorption that provides the coating with high frost resistance~~.	+

−	~~=== Wear Resistance ===~~	+	The destruction of the material occurs after the penetration of moisture into its pores, which begins to freeze, increases in volume and destroys the structure. Therefore, it is the low moisture absorption that provides the coating with high frost resistance.

−	~~<br />~~	+	= Wear resistance =
−	~~In addition, the main criterion of porcelain tiles used on the street is~~ resistance ~~to abrasion. The wear resistance of outdoor porcelain tiles is determined by three criteria: hardness, resistance to deep wear, resistance to wear.~~	+

−	~~According to EN 101,~~ the ~~MOHS scale~~ is ~~provided, according~~ to ~~which the material~~ is ~~assigned a~~ hardness ~~class (1 to 10) (where 1 is talc~~, ~~10 is diamond). For outdoor use, it is sufficient~~ to ~~use class 7 porcelain tiles according~~ to ~~MOHS~~.	+	The main criterion of porcelain tiles used on the street is resistance to abrasion. The wear resistance of outdoor porcelain tiles is determined by three criteria: hardness, resistance to deep wear and resistance to wear.

−	According to EN 154 (European standard), the tests are carried out with a corundum roller. Depending on the speed of this roller on the surface of the ~~[https://bluezonevitrified.com/large-porcelain-slab~~ porcelain tiles], which has not caused visible damage, the material is assigned a certain abrasion resistance class (PEI I - PEI V).	+	For outdoor use, it is sufficient to use class 7 porcelain tiles according to MOHS. The MOHS scale designates the hardness class of a material from one to 10 (where one is talc and 10 is diamond).
		+
		+	According to EN 154 (European standard), the tests are carried out with a corundum roller. Depending on the speed of this roller on the surface of the porcelain tiles, which has not caused visible damage, the material is assigned a certain abrasion resistance class (PEI I - PEI V).

	The deep wear resistance index is determined by the volume of material removed from the tile during a special test. For outdoor porcelain tiles, this figure is in the range of 110-140 mm. According to EN 102, the limit for floor coverings must not exceed 250 mm.		The deep wear resistance index is determined by the volume of material removed from the tile during a special test. For outdoor porcelain tiles, this figure is in the range of 110-140 mm. According to EN 102, the limit for floor coverings must not exceed 250 mm.

−	[[Category:Education]]	+	Related articles on Designing Buildings Wiki
		+
		+	[[Category:DCN_Product_Knowledge]] [[Category:Education]] [[Category:Products_/_components]]

Editor: moved Outdoor Porcelain TIles to Outdoor porcelain tiles

2021-05-24T16:38:17Z

moved Outdoor Porcelain TIles to Outdoor porcelain tiles

← Older revision

Revision as of 16:38, 24 May 2021

Priyasharma: Created page with "== Best Outdoor Porcelain Tiles == Among the large selection of floor coverings, porcelain tiles deserves special attention. Its aesthetic properties and technical characteristi..."

2021-05-10T12:21:14Z

Created page with "== Best Outdoor Porcelain Tiles == Among the large selection of floor coverings, porcelain tiles deserves special attention. Its aesthetic properties and technical characteristi..."

New page

== Best Outdoor Porcelain Tiles ==

Among the large selection of floor coverings, porcelain tiles deserves special attention. Its aesthetic properties and technical characteristics allow the material to be used everywhere. Today it can be placed in any room, regardless of its purpose, size, etc. There are several types of porcelain tiles, among which you can find the optimal model for any operating condition. Particular attention should be paid to [https://skytouchceramic.com/gvt-pgvt-outdoor-parking-tiles outdoor porcelain tiles], which has all the necessary properties to ensure the durability of the coating, even when used in an open space.

== Properties Of Outdoor Porcelain Tiles ==

=== Frost Resistance ===

<br />
The main indicator of exterior [https://cruso.in/polished-glazed-porcelain-tiles porcelain tiles] is the frost resistance of the material. This characteristic is determined through a series of tests. The essence of the test consists in the process of alternating freezing-thawing of the sample and studying the consequences of this effect. The national certification procedure foresees 50 freeze-thaw cycles, but in practice, porcelain tiles can withstand more than 200 cycles. Therefore, it can be safely placed on the street.

The material itself works perfectly in any temperature range (including frost down to -50 ° C).

In addition, there is a special frost-resistant outdoor porcelain tiles, which is ideal for laying in regions with a severe European climate.

=== Water Absorption ===

<br />
The high frost resistance of outdoor porcelain tiles is due to its low moisture absorption. The water absorption of this finishing material does not exceed 0.05% (very low). The destruction of the material occurs after the penetration of moisture into its pores, which begins to freeze, increases in volume and destroys the structure. Therefore, it is the low moisture absorption that provides the coating with high frost resistance.

=== Wear Resistance ===

<br />
In addition, the main criterion of porcelain tiles used on the street is resistance to abrasion. The wear resistance of outdoor porcelain tiles is determined by three criteria: hardness, resistance to deep wear, resistance to wear.

According to EN 101, the MOHS scale is provided, according to which the material is assigned a hardness class (1 to 10) (where 1 is talc, 10 is diamond). For outdoor use, it is sufficient to use class 7 porcelain tiles according to MOHS.

According to EN 154 (European standard), the tests are carried out with a corundum roller. Depending on the speed of this roller on the surface of the [https://bluezonevitrified.com/large-porcelain-slab porcelain tiles], which has not caused visible damage, the material is assigned a certain abrasion resistance class (PEI I - PEI V).

The deep wear resistance index is determined by the volume of material removed from the tile during a special test. For outdoor porcelain tiles, this figure is in the range of 110-140 mm. According to EN 102, the limit for floor coverings must not exceed 250 mm.

[[Category:Education]]