How to paint walls in eight steps - Revision history

88.108.166.107 at 10:42, 10 November 2022

2022-11-10T10:42:33Z

← Older revision		Revision as of 10:42, 10 November 2022
Line 3:		Line 3:
	= Introduction =		= Introduction =

−	First prepare the materials you need according to the product description and the different proportions of the preparation. Then gather the tools. Commonly used tools for wall painting include colour separation paper, kraft paper, wall painting rollers, brushes, putty knives, sandpaper and so on.	+	First prepare the materials you need according to the product description and the different proportions of the preparation. Then gather the tools. Commonly used tools for wall painting include colour separation paper, kraft paper, wall painting rollers, brushes, putty knives, sandpaper, dust sheets and so on.
		+
		+	To protect yourself from paint splashes wear overalls, gloves and goggles. If painting inside ensure that the room is well ventilated. Follow health and safety advice on the paint tin and if using a ladder.

	Steps and methods of operation include:		Steps and methods of operation include:
Line 17:		Line 19:
	When brushing the interface agent, it must be brushed evenly. It is possible to enhance the adhesion to the base layer, avoid the hollowing and shelling of the plaster layer. This replaces the manual chiseling process and can save time and effort.		When brushing the interface agent, it must be brushed evenly. It is possible to enhance the adhesion to the base layer, avoid the hollowing and shelling of the plaster layer. This replaces the manual chiseling process and can save time and effort.

−	= 3. Wall ~~leveling~~ =	+	= 3. Wall levelling =

−	Uneven walls should be ~~leveled~~ with plaster so that the error of the wall does not exceed 3 mm. If the angles are not straight, plaster should be applied and a ruler should be used to make sure it is straight.	+	Uneven walls should be levelled with plaster so that the error of the wall does not exceed 3 mm. If the angles are not straight, plaster should be applied and a ruler should be used to make sure it is straight.

	= 4. Apply the putty =		= 4. Apply the putty =
Line 44:		Line 46:

	Do not add too much water to the top paint and when painting, pay attention to the corners of the walls, the indirect stubble part of each roll, and the direction of the paint flow.		Do not add too much water to the top paint and when painting, pay attention to the corners of the walls, the indirect stubble part of each roll, and the direction of the paint flow.
		+
		+	Allow sufficient time before applying a second coat.
		+
		+	= 9. Cleaning Up and Disposal =
		+
		+	Wipe off as much paint as possible from the brush or roller against the edge of the tin. If using a water based paint wash the brush in water. If using a solvent based paint wash the brush in a solvent based cleaner. Solvent based cleaner can saved in a bottle for re-use.
		+
		+	Do not poor waste paint down the drain. It can clog up the drain, is bad for the environment and is illegal.
		+
		+	Give unused paint to family, friends or community paint recycling schemes.
		+
		+	Liquid paint should not be thrown out with general waste. Take the lid off the tin and leave it to go solid. Adding sawdust or sand can speed up this process.

	= Related articles on Designing Buildings =		= Related articles on Designing Buildings =

Designing Buildings at 08:53, 14 March 2022

2022-03-14T08:53:29Z

← Older revision		Revision as of 08:53, 14 March 2022
Line 1:		Line 1:
		+	This article needs more work - to help develop this article, click 'Edit this article' above.
		+
	= Introduction =		= Introduction =

−	First prepare the materials you need according to the product description and the different proportions of the preparation. Then gather the tools. Commonly used tools for wall painting include ~~color~~ separation paper, kraft paper, wall ~~paiting~~ rollers, brushes, putty knives, sandpaper and so on.	+	First prepare the materials you need according to the product description and the different proportions of the preparation. Then gather the tools. Commonly used tools for wall painting include colour separation paper, kraft paper, wall painting rollers, brushes, putty knives, sandpaper and so on.

	Steps and methods of operation include:		Steps and methods of operation include:
Line 7:		Line 9:
	= 1. Basic treatment =		= 1. Basic treatment =

−	Clean up the peeling and loose parts of the wall, and repair it with ~~cement mortar~~. Where there are cracks, kraft paper tape and white latex ~~are generally~~ used to stick to the cracks.	+	Clean up the peeling and loose parts of the wall, and repair it with an appropriate filler. Where there are cracks, kraft paper tape and white latex may be used to stick to the cracks.

−	~~Generally, non~~-load-bearing ~~walls such as lightweight walls and thermal insulation walls~~ need to be pasted. Try to choose better wall cloth and white latex or grid cloth. The grid cloth will have a better anti-cracking effect.	+	Non-load-bearing may need to be pasted. Try to choose better wall cloth and white latex or grid cloth. The grid cloth will have a better anti-cracking effect.

	= 2. The interface agent can be brushed =		= 2. The interface agent can be brushed =
Line 33:		Line 35:
	= 6. Apply primer =		= 6. Apply primer =

−	The primer must be evenly painted to ensure that every part of the wall is primed. If the ~~wall will have~~ a large amount of paint, it is best to add a little more water to the primer to ensure that the entire surface is covered.	+	The primer must be evenly painted to ensure that every part of the wall is primed. If the has a large amount of paint, it is best to add a little more water to the primer to ensure that the entire surface is covered.

	= 7. Look for blemishes =		= 7. Look for blemishes =
Line 50:		Line 52:
	* Paints and coatings.		* Paints and coatings.

−	[[Category:DCN_Guidance]] [[Category:Construction_techniques]]	+	[[Category:Articles_needing_more_work]] [[Category:DCN_Guidance]] [[Category:Construction_techniques]]

Editor at 17:41, 24 December 2021

2021-12-24T17:41:28Z

← Older revision		Revision as of 17:41, 24 December 2021
Line 49:		Line 49:
	* Paint.		* Paint.
	* Paints and coatings.		* Paints and coatings.
−	* Polished plaster.

	[[Category:DCN_Guidance]] [[Category:Construction_techniques]]		[[Category:DCN_Guidance]] [[Category:Construction_techniques]]

Editor at 17:38, 24 December 2021

2021-12-24T17:38:49Z

← Older revision		Revision as of 17:38, 24 December 2021
Line 7:		Line 7:
	= 1. Basic treatment =		= 1. Basic treatment =

−	Clean up the peeling and loose parts of the wall, and repair it with cement mortar. Where there are cracks, kraft paper tape and white latex are generally used to stick to the cracks. Generally, non-load-bearing walls such as lightweight walls and thermal insulation walls need to be pasted. Try to choose better wall cloth and white latex or grid cloth. The grid cloth will have a better anti-cracking effect.	+	Clean up the peeling and loose parts of the wall, and repair it with cement mortar. Where there are cracks, kraft paper tape and white latex are generally used to stick to the cracks.
		+
		+	Generally, non-load-bearing walls such as lightweight walls and thermal insulation walls need to be pasted. Try to choose better wall cloth and white latex or grid cloth. The grid cloth will have a better anti-cracking effect.

	= 2. The interface agent can be brushed =		= 2. The interface agent can be brushed =

−	~~Enhance~~ the adhesion to the base layer, avoid the hollowing and shelling of the plaster layer~~, thereby replacing~~ the manual chiseling process~~, saving~~ time and effort~~. When brushing the interface agent, it must be brushed evenly~~.	+	When brushing the interface agent, it must be brushed evenly. It is possible to enhance the adhesion to the base layer, avoid the hollowing and shelling of the plaster layer. This replaces the manual chiseling process and can save time and effort.

	= 3. Wall leveling =		= 3. Wall leveling =

−	~~The uneven wall needs to be leveled, and the uneven wall~~ should be leveled with plaster, so that the error of the wall does not exceed 3 mm. If the ~~yin and yang~~ angles are not straight, ~~plaster~~ plaster should be ~~used,~~ and a ruler should be used to make it straight.	+	Uneven walls should be leveled with plaster so that the error of the wall does not exceed 3 mm. If the angles are not straight, plaster should be applied and a ruler should be used to make sure it is straight.

	= 4. Apply the putty =		= 4. Apply the putty =

−	Putty with higher particle fineness and harder texture is better~~, and the putty~~ should be batched three times. The first pass is generally thicker because it involves levelling. The second and third passes are thinner, mainly for lightening, so that the wall looks smoother and flatter. After three batches, the thickness of the putty should not exceed ~~3mm~~, otherwise it will be easy to crack.	+	Putty with higher particle fineness and harder texture is better. Putty should be batched three times.
		+
		+	The first pass is generally thicker because it involves levelling. The second and third passes are thinner, mainly for lightening so that the wall looks smoother and flatter.
		+
		+	After three batches, the thickness of the putty should not exceed 3 mm, otherwise it will be easy to crack.

	= 5. Polish =		= 5. Polish =

−	This is a very critical step in the process~~. After polishing, the final paint effect can be good~~. Try to use finer sandpaper. If the sandpaper is too thick, it will leave deep marks. After polishing, be sure to clean the wall thoroughly to avoid too much dust ~~and affect~~ the adhesion of the paint~~. The unevenness is no more than 3 mm~~.	+	This is a very critical step in the process. Try to use finer sandpaper. If the sandpaper is too thick, it will leave deep marks. After polishing, be sure to clean the wall thoroughly to avoid too much dust, which will have an impact on the adhesion of the paint.

	= 6. Apply primer =		= 6. Apply primer =

−	The primer must be evenly painted to ensure that every part of the wall is ~~painted~~. If the wall ~~has~~ a large amount of paint, it is best to add a little more water to the primer to ensure that ~~it can be used. Apply evenly~~.	+	The primer must be evenly painted to ensure that every part of the wall is primed. If the wall will have a large amount of paint, it is best to add a little more water to the primer to ensure that the entire surface is covered.

	= 7. Look for blemishes =		= 7. Look for blemishes =

−	After the putty is polished, there will be some blemishes. Under normal circumstances, it is difficult to see clearly. It will be obvious only after brushing the paint once. At this time, it is necessary to ~~find~~ repairs. ~~Pay attention that you must~~ polish ~~it evenly,~~ and ~~then use a~~ primer ~~with a little more water to avoid color difference when you paint the top paint because of~~ the ~~difference in draft from other walls~~.	+	After the putty is polished, there will be some blemishes. Under normal circumstances, it may be difficult to see clearly. It will be obvious only after brushing the paint once. At this time, it is necessary to check for repairs. See if the polish is even and the primer is applied across the entire surface.

	= 8. Work carefully =		= 8. Work carefully =

−	Do not add too much water to the top paint~~, which will affect it. The thickness, feel~~ and ~~hardness of the paint film. Try to choose better tools. When~~ painting, pay attention to the corners of the walls, the indirect stubble part of each roll, and the direction of the paint ~~collection~~.	+	Do not add too much water to the top paint and when painting, pay attention to the corners of the walls, the indirect stubble part of each roll, and the direction of the paint flow.
		+
		+	= Related articles on Designing Buildings =

−	~~Related articles on Designing Buildings~~	+	* Decoration.
		+	* Finishes.
		+	* Paint.
		+	* Paints and coatings.
		+	* Polished plaster.

−	[[Category:Construction_techniques]]	+	[[Category:DCN_Guidance]] [[Category:Construction_techniques]]

Editor: moved Eight steps to teach you to paint the walls yourself to How to paint walls in eight steps

2021-12-24T17:28:25Z

moved Eight steps to teach you to paint the walls yourself to How to paint walls in eight steps

← Older revision

Revision as of 17:28, 24 December 2021

Editor at 17:27, 24 December 2021

2021-12-24T17:27:45Z

← Older revision		Revision as of 17:27, 24 December 2021
Line 1:		Line 1:
−	Preparation of materials for the steps of painting the walls yourself: cement mortar, interface agent, putty powder, wall paint, etc. First prepare the materials you need, and then according to the product description, according to the different proportions of the preparation. Tool preparation: The commonly used tools for wall painting include color separation paper, kraft paper, [https://www.cohwabrush.com/foam-paint-roller/9inch-foam-paint-roller.html wall paiting rollers], brushes, [https://www.cohwabrush.com/putty-knives/putty-knife-4-inch.html putty knives,] sandpaper, etc. Steps and methods of operation: 1. Basic treatment: Clean up the peeling and loose parts of the wall, and repair it with cement mortar. Where there are cracks, kraft paper tape and white latex are generally used to stick to the cracks. Generally, non-load-bearing walls such as light-weight walls and thermal insulation walls need to be pasted. Try to choose better wall cloth and white latex or grid cloth. The grid cloth will have a better anti-cracking effect. 2. The interface agent can be brushed. Enhance the adhesion to the base layer, avoid the hollowing and shelling of the plaster layer, thereby replacing the manual chiseling process, saving time and effort. When brushing the interface agent, it must be brushed evenly. 3. Wall leveling The uneven wall needs to be leveled, and the uneven wall should be leveled with plaster, so that the error of the wall does not exceed 3 mm. If the yin and yang angles are not straight, plaster plaster should be used, and a ruler should be used to make it straight.[https://www.cohwabrush.com/uploadfile/2016/0523/20160523100753783.jpg https://www.cohwabrush.com/uploadfile/2016/0523/20160523100753783.jpg]	+	= Introduction =

−	4. Putty with higher particle fineness and harder texture is better, and the putty should be batched three times. The first pass is generally thicker because it involves levelling. The second and third passes are thinner, mainly for lightening, so that the wall looks smoother and flatter. After three batches, the thickness of the putty should not exceed 3mm, otherwise it will be easy to crack. 5. ~~Polishing~~ is a very critical step in the ~~painter's steps~~. After polishing, the final paint effect can be good. Try to use finer sandpaper. If the sandpaper is too thick, it will leave deep marks. After polishing, be sure to clean the wall thoroughly to avoid too much dust and affect the adhesion of the paint. The unevenness is no more than 3 mm. 6. The primer must be evenly painted to ensure that every part of the wall is painted. If the wall has a large amount of paint, it is best to add a little more water to the primer to ensure that it can be used. Apply evenly. 7. After the putty is polished, there will be some blemishes. Under normal circumstances, it is difficult to see clearly. It will be obvious only after brushing the paint once. At this time, it is necessary to find repairs. Pay attention that you must polish it evenly, and then use a primer with a little more water to avoid color difference when you paint the top paint because of the difference in draft from other walls. 8. Do not add too much water to the top paint, which will affect it. The thickness, feel and hardness of the paint film. Try to choose better tools. When painting, pay attention to the corners of the walls, the indirect stubble part of each roll, and the direction of the paint collection. The surface paint is generally painted twice and the [https://www.cohwabrush.com/foam-paint-roller/9inch-foam-paint-roller.html wall paint] construction process has eight main steps, followed by basic treatment, brushing interface agent, wall leveling, scraping putty, sanding the wall, brushing the primer, repairing the wall, and brushing the surface. paint. Each step has its own operation method and construction requirements. When painting the wall, you need to do each step well in accordance with the specific requirements.	+	First prepare the materials you need according to the product description and the different proportions of the preparation. Then gather the tools. Commonly used tools for wall painting include color separation paper, kraft paper, wall paiting rollers, brushes, putty knives, sandpaper and so on.
		+
		+	Steps and methods of operation include:
		+
		+	= 1. Basic treatment =
		+
		+	Clean up the peeling and loose parts of the wall, and repair it with cement mortar. Where there are cracks, kraft paper tape and white latex are generally used to stick to the cracks. Generally, non-load-bearing walls such as lightweight walls and thermal insulation walls need to be pasted. Try to choose better wall cloth and white latex or grid cloth. The grid cloth will have a better anti-cracking effect.
		+
		+	= 2. The interface agent can be brushed =
		+
		+	Enhance the adhesion to the base layer, avoid the hollowing and shelling of the plaster layer, thereby replacing the manual chiseling process, saving time and effort. When brushing the interface agent, it must be brushed evenly.
		+
		+	= 3. Wall leveling =
		+
		+	The uneven wall needs to be leveled, and the uneven wall should be leveled with plaster, so that the error of the wall does not exceed 3 mm. If the yin and yang angles are not straight, plaster plaster should be used, and a ruler should be used to make it straight.
		+
		+	= 4. Apply the putty =
		+
		+	Putty with higher particle fineness and harder texture is better, and the putty should be batched three times. The first pass is generally thicker because it involves levelling. The second and third passes are thinner, mainly for lightening, so that the wall looks smoother and flatter. After three batches, the thickness of the putty should not exceed 3mm, otherwise it will be easy to crack.
		+
		+	= 5. Polish =
		+
		+	This is a very critical step in the process. After polishing, the final paint effect can be good. Try to use finer sandpaper. If the sandpaper is too thick, it will leave deep marks. After polishing, be sure to clean the wall thoroughly to avoid too much dust and affect the adhesion of the paint. The unevenness is no more than 3 mm.
		+
		+	= 6. Apply primer =
		+
		+	The primer must be evenly painted to ensure that every part of the wall is painted. If the wall has a large amount of paint, it is best to add a little more water to the primer to ensure that it can be used. Apply evenly.
		+
		+	= 7. Look for blemishes =
		+
		+	After the putty is polished, there will be some blemishes. Under normal circumstances, it is difficult to see clearly. It will be obvious only after brushing the paint once. At this time, it is necessary to find repairs. Pay attention that you must polish it evenly, and then use a primer with a little more water to avoid color difference when you paint the top paint because of the difference in draft from other walls.
		+
		+	= 8. Work carefully =
		+
		+	Do not add too much water to the top paint, which will affect it. The thickness, feel and hardness of the paint film. Try to choose better tools. When painting, pay attention to the corners of the walls, the indirect stubble part of each roll, and the direction of the paint collection.
		+
		+	Related articles on Designing Buildings

	[[Category:Construction_techniques]]		[[Category:Construction_techniques]]

Cohwabrush: Created page with "Preparation of materials for the steps of painting the walls yourself: cement mortar, interface agent, putty powder, wall paint, etc. First prepare the materials you need, and th..."

2021-12-22T06:36:19Z

Created page with "Preparation of materials for the steps of painting the walls yourself: cement mortar, interface agent, putty powder, wall paint, etc. First prepare the materials you need, and th..."

New page

Preparation of materials for the steps of painting the walls yourself: cement mortar, interface agent, putty powder, wall paint, etc. First prepare the materials you need, and then according to the product description, according to the different proportions of the preparation. Tool preparation: The commonly used tools for wall painting include color separation paper, kraft paper, [https://www.cohwabrush.com/foam-paint-roller/9inch-foam-paint-roller.html wall paiting rollers], brushes, [https://www.cohwabrush.com/putty-knives/putty-knife-4-inch.html putty knives,] sandpaper, etc. Steps and methods of operation: 1. Basic treatment: Clean up the peeling and loose parts of the wall, and repair it with cement mortar. Where there are cracks, kraft paper tape and white latex are generally used to stick to the cracks. Generally, non-load-bearing walls such as light-weight walls and thermal insulation walls need to be pasted. Try to choose better wall cloth and white latex or grid cloth. The grid cloth will have a better anti-cracking effect. 2. The interface agent can be brushed. Enhance the adhesion to the base layer, avoid the hollowing and shelling of the plaster layer, thereby replacing the manual chiseling process, saving time and effort. When brushing the interface agent, it must be brushed evenly. 3. Wall leveling The uneven wall needs to be leveled, and the uneven wall should be leveled with plaster, so that the error of the wall does not exceed 3 mm. If the yin and yang angles are not straight, plaster plaster should be used, and a ruler should be used to make it straight.[https://www.cohwabrush.com/uploadfile/2016/0523/20160523100753783.jpg https://www.cohwabrush.com/uploadfile/2016/0523/20160523100753783.jpg]

4. Putty with higher particle fineness and harder texture is better, and the putty should be batched three times. The first pass is generally thicker because it involves levelling. The second and third passes are thinner, mainly for lightening, so that the wall looks smoother and flatter. After three batches, the thickness of the putty should not exceed 3mm, otherwise it will be easy to crack. 5. Polishing is a very critical step in the painter's steps. After polishing, the final paint effect can be good. Try to use finer sandpaper. If the sandpaper is too thick, it will leave deep marks. After polishing, be sure to clean the wall thoroughly to avoid too much dust and affect the adhesion of the paint. The unevenness is no more than 3 mm. 6. The primer must be evenly painted to ensure that every part of the wall is painted. If the wall has a large amount of paint, it is best to add a little more water to the primer to ensure that it can be used. Apply evenly. 7. After the putty is polished, there will be some blemishes. Under normal circumstances, it is difficult to see clearly. It will be obvious only after brushing the paint once. At this time, it is necessary to find repairs. Pay attention that you must polish it evenly, and then use a primer with a little more water to avoid color difference when you paint the top paint because of the difference in draft from other walls. 8. Do not add too much water to the top paint, which will affect it. The thickness, feel and hardness of the paint film. Try to choose better tools. When painting, pay attention to the corners of the walls, the indirect stubble part of each roll, and the direction of the paint collection. The surface paint is generally painted twice and the [https://www.cohwabrush.com/foam-paint-roller/9inch-foam-paint-roller.html wall paint] construction process has eight main steps, followed by basic treatment, brushing interface agent, wall leveling, scraping putty, sanding the wall, brushing the primer, repairing the wall, and brushing the surface. paint. Each step has its own operation method and construction requirements. When painting the wall, you need to do each step well in accordance with the specific requirements.

[[Category:Construction_techniques]]