Dovetail joint - Revision history

Editor at 20:43, 26 August 2024

2024-08-26T20:43:42Z

← Older revision		Revision as of 20:43, 26 August 2024
Line 10:		Line 10:
	* Sliding dovetail is a dovetail used in a groove in the centre of a board, the adjoining piece and fitting dovetail is attached by sliding it from one egde. These kind of joints might be used for bid point shelves.		* Sliding dovetail is a dovetail used in a groove in the centre of a board, the adjoining piece and fitting dovetail is attached by sliding it from one egde. These kind of joints might be used for bid point shelves.

−	[[Category:~~Articles_needing_more_work~~]]	+	= Related articles on Designing Buildings =
		+
		+	* Assembly.
		+	* Building complex.
		+	* Building element.
		+	* Building entities.
		+	* Building spaces.
		+	* Building system.
		+	* Component.
		+	* Concrete joint.
		+	* Connection.
		+	* Construction joint.
		+	* Contraction joint.
		+	* Crack control joint.
		+	* Daywork joint.
		+	* Dowelled joint.
		+	* Expansion joint.
		+	* Finger joint.
		+	* Joggle joint.
		+	* Joint v connection.
		+	* Junction.
		+	* Mitre.
		+	* Mortar joint.
		+	* Mortise and tenon joint.
		+	* Movement joint.
		+	* Off-site prefabrication of buildings: A guide to connection choices.
		+	* Road joints.
		+	* Rub joint.
		+	* Scarf joint.
		+	* Shrinkage joint.
		+	* Tongue and groove joint.
		+	* Warping joint.
		+
		+	[[Category:DCN_Commentary]] [[Category:DCN_Definition]] [[Category:DCN_Product_Knowledge]] [[Category:Definitions]] [[Category:Construction_techniques]] [[Category:Products_/_components]]

Editor at 20:41, 26 August 2024

2024-08-26T20:41:43Z

← Older revision		Revision as of 20:41, 26 August 2024
Line 1:		Line 1:
	A dovetail joint is a carpentry connection in which the tenon or tenons (the projecting element) are tapered on both sides, these interlock with corresponding mortise or mortises (notched or recessed element) tapered in the opposite direction. By the nature of tapered or wedge elements the two pieces are are installed from the sides, and once in position are effectively locked in place unable to come apart directly, unlike a standard square mortise and tenon joint which can.		A dovetail joint is a carpentry connection in which the tenon or tenons (the projecting element) are tapered on both sides, these interlock with corresponding mortise or mortises (notched or recessed element) tapered in the opposite direction. By the nature of tapered or wedge elements the two pieces are are installed from the sides, and once in position are effectively locked in place unable to come apart directly, unlike a standard square mortise and tenon joint which can.
		+
		+	The dovetail joint is said to date back as far as the Egyptians, as such joints have been found on Egyptian furniture entombed with mummies which date from First Dynasty, aswell as tombs of Chinese emperors. In Europe dovetails started to be used in furniture pieces around the 1600s, ofrten for cabinet and chests of drawers.
		+
		+	In general there are considered to be a number of different variations on the dovetail joint, of differing complexity in termas of craftsmanship.
		+
		+	* Through dovetail is the standard and most common dovetail joint, where the tapered cuts run through the depth ogf the wood and are the same size as the corner joint .
		+	* Half-blind dovetail is the same on one side, but on the other the cuts are not through cuts but around two thirds the depth of the timber. This results in the dovetails being exposed or see from the outside on only one side, rather than the two sides, as might be used in a the facing panel of a drawer.
		+	* Secret mitered dovetail is effectively a double blind dovetail (also called a mitered or full blind dovetail), and as such on both elements the diovetail cuts run only two thirds the depth of the timber. This hides the dove tail joint within the timber depth and thus the dovetails cannot be seen from the front or the side.
		+	* Sliding dovetail is a dovetail used in a groove in the centre of a board, the adjoining piece and fitting dovetail is attached by sliding it from one egde. These kind of joints might be used for bid point shelves.

	[[Category:Articles_needing_more_work]]		[[Category:Articles_needing_more_work]]

Editor: Created page with "A dovetail joint is a carpentry connection in which the tenon or tenons (the projecting element) are tapered on both sides, these interlock with corresponding mortise or mortises..."

2024-08-26T20:28:21Z

Created page with "A dovetail joint is a carpentry connection in which the tenon or tenons (the projecting element) are tapered on both sides, these interlock with corresponding mortise or mortises..."

New page

A dovetail joint is a carpentry connection in which the tenon or tenons (the projecting element) are tapered on both sides, these interlock with corresponding mortise or mortises (notched or recessed element) tapered in the opposite direction. By the nature of tapered or wedge elements the two pieces are are installed from the sides, and once in position are effectively locked in place unable to come apart directly, unlike a standard square mortise and tenon joint which can.

[[Category:Articles_needing_more_work]]