BS EN 15037-1 - Revision history

Designing Buildings at 08:38, 31 December 2020

2020-12-31T08:38:13Z

← Older revision		Revision as of 08:38, 31 December 2020
Line 30:		Line 30:
	* Types of floor.		* Types of floor.

−	[[Category:~~Publications_/_reports~~]] [[Category:~~Standards_/_measurements~~]] [[Category:DCN_Standard]]	+	[[Category:DCN_Definition]] [[Category:DCN_Guidance]] [[Category:DCN_Standard]] [[Category:Publications_/_reports]] [[Category:Standards_/_measurements]]

Designing Buildings at 08:04, 13 September 2017

2017-09-13T08:04:25Z

← Older revision		Revision as of 08:04, 13 September 2017
Line 1:		Line 1:
−	BS EN 15037-1:2008 ‘Precast concrete products. Beam-and-block floor systems. Beams’ is a British-adopted European Standard which came into force in 2008.	+	[https://shop.bsigroup.com/ProductDetail/?pid=000000000030122797 BS EN 15037-1:2008] ‘Precast concrete products. Beam-and-block floor systems. Beams’ is a British-adopted European Standard which came into force in 2008.

−	It provides requirements, test methods and evaluation of conformity for precast beams using reinforced or prestressed normal or lightweight concrete ~~that are~~ intended for use in structural floor and roof systems~~. It refers to concrete beams which provide the final strength of the floor system, independently of any other component part of the system~~.	+	It provides requirements, test methods and evaluation of conformity for precast beams using reinforced or prestressed normal or lightweight concrete intended for use in structural floor and roof systems.

−	~~The standard~~ also refers to semi- or resisting concrete blocks that transfer the floor load onto the self-bearing beams. The final strength of the floor is achieved in conjunction with a concrete topping and can also be with concrete blocks.	+	It refers to concrete beams which provide the final strength of the floor system, independently of any other component part of the system. It also refers to semi- or resisting concrete blocks that transfer the floor load onto the self-bearing beams. The final strength of the floor is achieved in conjunction with a concrete topping and can also be with concrete blocks.

	It is published is published in parts 1 to 5:		It is published is published in parts 1 to 5:
Line 13:		Line 13:
	* Part 5 - Lightweight Blocks for simple formwork		* Part 5 - Lightweight Blocks for simple formwork

−	In addition to the beam and block/infill specification, consideration must also be given to the floor finish. This will largely be dependent on the type of substrate, the beam and infill system used and whether that system is deemed to be self-bearing or non-self-bearing ~~as defined in BS EN 15037-1~~.	+	In addition to the beam and block/infill specification, consideration must also be given to the floor finish. This will largely be dependent on the type of substrate, the beam and infill system used and whether that system is deemed to be self-bearing or non-self-bearing.

−	The standard states it is essential that the beam’s total depth be between 60-300 mm and ~~the~~ beams be placed at centres of no more than 1 m. Precast concrete beams of higher depth should comply with EN 13225.	+	The standard states that it is essential that the beam’s total depth is between 60-300 mm and beams are placed at centres of no more than 1 m. Precast concrete beams of higher depth should comply with EN 13225.
−		+
−	~~You can purchase the standard from BSI~~.	+

	= Find out more =		= Find out more =
Line 32:		Line 30:
	* Types of floor.		* Types of floor.

−	[[Category:Publications_/_reports]] [[Category:Standards_/_measurements]]	+	[[Category:Publications_/_reports]] [[Category:Standards_/_measurements]] [[Category:DCN_Standard]]

Editor: Created page with "BS EN 15037-1:2008 ‘Precast concrete products. Beam-and-block floor systems. Beams’ is a British-adopted European Standard which came into force in 2008. It provides require..."

2017-09-11T12:37:50Z

Created page with "BS EN 15037-1:2008 ‘Precast concrete products. Beam-and-block floor systems. Beams’ is a British-adopted European Standard which came into force in 2008. It provides require..."

New page

BS EN 15037-1:2008 ‘Precast concrete products. Beam-and-block floor systems. Beams’ is a British-adopted European Standard which came into force in 2008.

It provides requirements, test methods and evaluation of conformity for precast beams using reinforced or prestressed normal or lightweight concrete that are intended for use in structural floor and roof systems. It refers to concrete beams which provide the final strength of the floor system, independently of any other component part of the system.

The standard also refers to semi- or resisting concrete blocks that transfer the floor load onto the self-bearing beams. The final strength of the floor is achieved in conjunction with a concrete topping and can also be with concrete blocks.

It is published is published in parts 1 to 5:

* Part 1 - Beams
* Part 2 - Concrete Blocks
* Part 3 - Clay Blocks
* Part 4 - Expanded Polystyrene Blocks
* Part 5 - Lightweight Blocks for simple formwork

In addition to the beam and block/infill specification, consideration must also be given to the floor finish. This will largely be dependent on the type of substrate, the beam and infill system used and whether that system is deemed to be self-bearing or non-self-bearing as defined in BS EN 15037-1.

The standard states it is essential that the beam’s total depth be between 60-300 mm and the beams be placed at centres of no more than 1 m. Precast concrete beams of higher depth should comply with EN 13225.

You can purchase the standard from BSI.

= Find out more =

=== Related articles on Designing Buildings Wiki ===

* Beam and Infill Suspended Floors.
* Concrete.
* Design of durable concrete structures.
* Floor loading.
* Precast concrete.
* Prestressed concrete.
* Reinforced concrete.
* Types of floor.

[[Category:Publications_/_reports]] [[Category:Standards_/_measurements]]