Designing Buildings at 07:17, 14 February 2022

2022-02-14T07:17:51Z

← Older revision		Revision as of 07:17, 14 February 2022
Line 1:		Line 1:
−	~~= Definition =~~	+	Angular Selectivity is a special case of angular dependence. Angle dependant performance simply means that the relevant property, for example, the transmittance through or reflectance from an illuminated surface takes on different numerical values for different angles of incidence.

−	Angular Selectivity is a special case of angular dependence. Angle dependant performance simply means that the relevant property, for example, the transmittance through or reflectance from the illuminated surface takes on different numerical values for different angles of incidence. The angle of incidence, which is often designated "theta” is the angle subtended between the normal or perpendicular plane to a given surface and a ray of incoming (incident) light. A common example is that any ordinary pane of clear glass will have its highest transmittance value (and lowest reflectance value) for theta = 0° and its lowest transmittance value (namely zero) and highest reflectance value for theta = 90°.	+	The angle of incidence, which is often designated "theta” is the angle subtended between the normal or perpendicular plane to a given surface and a ray of incoming (incident) light. A common example is that any ordinary pane of clear glass will have its highest transmittance value (and lowest reflectance value) for theta = 0° and its lowest transmittance value (namely zero) and highest reflectance value for theta = 90°.

−	To define Angular Selectivity, we need to introduce a second angle, namely an azimuthal angle or "phi", which describes rotation around the surface normal in a plane parallel to the surface. It is only of interest if the surface is not homogeneous but has some structure which varies according to the azimuthal angle. Taking a vertically mounted projection and defining the upward direction by phi = 0°, we have angle selective behaviour, because the transmittance for a given fixed theta value is different for different phi values. Using a lamella or louvre array as an example, when theta = 40 ° and phi = 0°, the transmittance is quite low, whereas for theta = 10° and phi = 180°, the transmittance is higher. If different amounts of light are transmitted, for the same angle of incidence theta, depending on whether the light comes from above or below then the sample is angle selective. By contrast, a homogeneous material like a pane of clear is not angle selective; it always has the same transmittance value for a given theta, independent of the value of phi.	+	To define Angular Selectivity, we need to introduce a second angle, namely an azimuthal angle or "phi", which describes rotation around the surface normal in a plane parallel to the surface. It is only of interest if the surface is not homogeneous but has some structure which varies according to the azimuthal angle.

−	[[Category:Definitions]] [[Category:~~Education~~]]	+	Taking a vertically mounted projection and defining the upward direction by phi = 0°, we have angle selective behaviour, because the transmittance for a given fixed theta value is different for different phi values. Using a lamella or louvre array as an example, when theta = 40 ° and phi = 0°, the transmittance is quite low, whereas for theta = 10° and phi = 180°, the transmittance is higher.
		+
		+	If different amounts of light are transmitted, for the same angle of incidence theta, depending on whether the light comes from above or below then the sample is angle selective. By contrast, a homogeneous material like a pane of clear glass is not angle selective; it always has the same transmittance value for a given theta, independent of the value of phi.
		+
		+	= Related articles on Designing Buildings. =
		+
		+	* Electromagnetic energy.
		+	* Electromagnetic spectrum.
		+	* Emissivity.
		+	* g-value.
		+	* Gamma rays.
		+	* Light reflectance value.
		+	* Low-e glass.
		+	* Optical properties.
		+	* Shading coefficient.
		+	* Solar gain.
		+	* Solar heat gain coefficient.
		+	* Solar transmittance (gtot).
		+	* Transparent.
		+	* Visible light.
		+
		+	[[Category:DCN_Definition]] [[Category:Definitions]] [[Category:Standards_/_measurements]]

Koolshademaker: Created page with "= Definition = Angular Selectivity is a special case of angular dependence. Angle dependant performance simply means that the relevant property, for example, the transmittance t..."

2022-01-06T13:42:32Z

Created page with "= Definition = Angular Selectivity is a special case of angular dependence. Angle dependant performance simply means that the relevant property, for example, the transmittance t..."

New page

= Definition =

Angular Selectivity is a special case of angular dependence. Angle dependant performance simply means that the relevant property, for example, the transmittance through or reflectance from the illuminated surface takes on different numerical values for different angles of incidence. The angle of incidence, which is often designated "theta” is the angle subtended between the normal or perpendicular plane to a given surface and a ray of incoming (incident) light. A common example is that any ordinary pane of clear glass will have its highest transmittance value (and lowest reflectance value) for theta = 0° and its lowest transmittance value (namely zero) and highest reflectance value for theta = 90°.

To define Angular Selectivity, we need to introduce a second angle, namely an azimuthal angle or "phi", which describes rotation around the surface normal in a plane parallel to the surface. It is only of interest if the surface is not homogeneous but has some structure which varies according to the azimuthal angle. Taking a vertically mounted projection and defining the upward direction by phi = 0°, we have angle selective behaviour, because the transmittance for a given fixed theta value is different for different phi values. Using a lamella or louvre array as an example, when theta = 40 ° and phi = 0°, the transmittance is quite low, whereas for theta = 10° and phi = 180°, the transmittance is higher. If different amounts of light are transmitted, for the same angle of incidence theta, depending on whether the light comes from above or below then the sample is angle selective. By contrast, a homogeneous material like a pane of clear is not angle selective; it always has the same transmittance value for a given theta, independent of the value of phi.

[[Category:Definitions]] [[Category:Education]]

Angular selective - Revision history

Designing Buildings at 07:17, 14 February 2022

Koolshademaker: Created page with "= Definition = Angular Selectivity is a special case of angular dependence. Angle dependant performance simply means that the relevant property, for example, the transmittance t..."